高純度の取得トキソプラズマオーシスト

1. General safety precautions when working with T. gondii oocysts It is important to follow all safety precautions when working with T. gondii oocysts. In most healthy individuals, T. gondii infection is readily controlled by the immune system; however, a life-long infection results. Immunocompromised individuals are particularly susceptible to toxoplasmosis and should not handle T. gondii oocysts. Pregnant women should also not handle T. gondii oocysts, because infection can cause severe birth defects8. T. gondii oocysts should only be handled in a designated area and with trained personnel. Signs indicating T. gondii oocyst work is in progress must be posted to alert others entering the designated area. Wear appropriate personal protective equipment (PPE) such as a lab coat, disposable gown, disposable gloves, and proper eye protection or a face shield when handling T. gondii oocysts. Frequent glove changes are recommended. Do not handle any lab equipment with T. gondii oocyst contaminated gloves. Always use metal autoclavable trays lined with a disposable absorbent liners when working with T. gondii oocysts. Ensure all racks, tubes, etc. used are either disposable or autoclavable. All T. gondii waste must be autoclaved twice for at least one hour. All non-disposable equipment (racks, trays, etc.) must also be autoclaved twice for at least one hour. Vacuum lines used to aspirate liquids should be connected to a Vacushield™ filter to prevent contamination of the vacuum pump. All affected laboratory bench-tops must be disinfected after completing work with T. gondii oocysts. Freshly made 10% hypochlorite should be liberally applied to the work area and allowed dry. The area must then be rinsed well with water. 2. Preparation of buffers and solutions Prepare a 1 L 2.2 M solution of sucrose by dissolving 752.66 g of sucrose in 600 ml ddH2O. Stir and heat gently using a heated stir plate to dissolve the sucrose. Once completely dissolved, bring volume to 1 L with ddH2O. This should be followed by sterilization by autoclaving the solution for at least 20 minutes. Prepare a 1L TE buffer (50 mM Tris-HCl, 10 mM EDTA), pH 7.2 by adding 6.05 g of Tris-HCl and 3.7 g of EDTA in 700 ml of ddH2O, adjust pH to 7.2 then bring volume to 1 L with ddH2O. For the CsCl gradient, prepare a stock solution of CsCl with a specific gravity of 1.15 (1.15-CsCl) by adding 21.75 g of CsCl with 103.25 ml of TE Buffer. For Solution A, mix 30 ml of TE with 20 ml of 1.15-CsCl. For Solution B, mix 20 ml of TE with 30 ml of 1.15-CsCl and 12.5 μl of phenol red solution. For Solution C, mix 10 ml of TE with 40 ml of 1.15-CsCl (Table 1). Prepare a 1L 1 N solution of sodium hydroxide (NaOH) by dissolving 40 g of NaOH, in 800 ml of ddH2O. Once dissolved, bring volume to 1 L with ddH2O. Prepare a 1 L 2% (by volume) solution of H2SO4 mixing 20 ml of H2SO4 with 980 ml of ddH2O. 3. Sucrose float Add 10 ml of a fecal suspension of T. gondii oocysts, in 2% H2SO4, into a 50 ml conical centrifuge tube. It must be noted that fecal suspension refers to samples that have been pre-processed through a sucrose flotation procedure as previously described8. When the fecal samples are initially harvested from the infected cats they are processed through a sucrose float as described in reference 8. This additional sucrose float is necessary to further minimize fecal debris carried over to the CsCl purification process and obtain the purest T. gondii oocysts possible. Neutralize the 2% H2SO4 by adding 6 ml (3/5 volumes) of 1 N NaOH to the fecal suspension. Mix well by vortexing. Add an equal volume (16 ml) of 2.2 M sucrose creating a final concentration of 1.1 M to the fecal suspension and mix well by vortexing. Carefully overlay the sucrose/fecal suspension with 10 ml ddH2O using a 10 ml pipette. Centrifuge the suspension at 1,200 x g for 20 min at room temperature with no brake. Carefully collect the top water and interphase layers and transfer to a new 50 ml conical centrifuge tube by pipetting from the air-water interface without swirling the pipette. It is important to minimize sucrose carryover while collecting the interphase layer. Mix the remaining sucrose/fecal pellet solution by vortexing the tube. Repeat steps 3.4 and 3.5. Bring the volume of the two oocyst interphase solutions to 50 ml with ddH2O and centrifuge the tubes at 2,000 x g for 10 minutes at room temperature. Aspirate the supernatant from each tube and resuspend pellets with 5 ml TE buffer and pool the oocyst suspension together. The total pooled volume should be 10 ml. 4. CsCl gradient Prepare a discontinuous CsCl gradient in a 50 ml polycarbonate Oak Ridge tube by carefully underlaying each layer using a 50 ml syringe with an 18 gauge blunt-ended, autoclavable, steel needle, and a 2 way stop cock. Note: Phenol red is added to Solution B to easily distinguish between the gradient layers (Table 1). Slowly add the following solutions to the tube in the order listed below. It should be noted that the flow rate should not exceed more than 0.5 ml/sec. 10 ml of the TE/oocyst suspension sample 8 ml Solution A 8 ml Solution B 8 ml Solution C Centrifuge the Oak Ridge tube at 12,000 x g for 60 min at 4 °C with no brake. Use of a fixed angle rotor is acceptable, but a high speed swinging bucket results in better separation of the oocysts from the suspension sample with minimal fecal debris smears along the side or the tube. The extent of the smears depends on the composition of the fecal suspension and thus it may be necessary to perform two CsCl gradients if the fecal suspension is extremely dirty. Following centrifugation, collect the opaque/white oocyst containing band between solutions A and B. To minimize contamination with fecal debris, go directly to the oocyst band without disturbing the gradient and collect the oocyst interphase using a 10 ml pipette. Transfer the oocyst interphase to a new 50 ml conical centrifuge tube. Try to minimize the amount of CsCl solution aspirated while collecting the oocyst interphase as it may pose a problem in pelleting the oocysts during the wash step. Wash oocysts with 30-40 ml of ddH2O. Centrifuge the tube at 2,000 x g at room temperature for 10 min with no brake. Carefully aspirate the supernatant without disturbing the oocyst pellet. Repeat the wash 2 additional times. At the end of the final wash, carefully aspirate the supernatant and resuspend the pellet in 10 ml 2% sulfuric acid and store at 4 °C until use. Oocysts are now ready for further manipulation. Oocyst purity can be checked microscopically by the absence of fecal debris in the sample.