Application of the Intelligent High-Throughput Antimicrobial Sensitivity Testing/Phage Screening System and Lar Index of Antimicrobial Resistance

Ming Hu; Zhengjie Liu; Ziang Song; Lulu Li; Xiaonan Zhao; Yanbo Luo; Qing Zhang; Yibao Chen; Xiaohui Xu; Yahui Dong; Nataliia Hrabchenko; Wei Zhang; Yuqing Liu

doi:10.3791/64785

JoVE Journal > Environment

Medio ambiente

Application of the Intelligent High-Throughput Antimicrobial Sensitivity Testing/Phage Screening System and Lar Index of Antimicrobial Resistance

Published: July 21, 2023

doi:

10.3791/64785

Ming Hu¹, Zhengjie Liu^1,2, Ziang Song^1,3, Lulu Li¹, Xiaonan Zhao¹, Yanbo Luo¹, Qing Zhang¹, Yibao Chen¹, Xiaohui Xu¹, Yahui Dong¹, Nataliia Hrabchenko¹, Wei Zhang³, Yuqing Liu¹

¹Shandong Key Laboratory of Animal Disease Control and Breeding, Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences, P.R. China,Key Laboratory of Livestock and Poultry Multi-omics of MARA, ²Department of Genetic and Genomes Biology,University of Leicester, ³College of Veterinary Medicine,Nanjing Agricultural University

Summary

Here we introduce the principle, structure, and instruction of the intelligent high-throughput antimicrobial sensitivity testing/phage screening system. Its application is illustrated by using Salmonella isolated from poultry in Shandong, China, as an example. The Lar index is calculated, and its significance in evaluating antimicrobial resistance is discussed comprehensively.

Abstract

To improve the efficiency of antimicrobial susceptibility testing (AST) and phage high-throughput screening for resistant bacteria and to reduce the detection cost, an intelligent high-throughput AST/phage screening system, including a 96-dot matrix inoculator, image acquisition converter, and corresponding software, was developed according to AST criteria and the breakpoints of resistance (R) formulated by the Clinical & Laboratory Standards Institute (CLSI). AST and statistics of minimum inhibitory concentration (MIC) distributions (from R/8 to 8R) of 1,500 Salmonella strains isolated from poultry in Shandong, China, against 10 antimicrobial agents were carried out by the intelligent high-throughput AST/phage screening system. The Lar index, meaning “less antibiosis, less resistance and residual until little antibiosis”, was obtained by calculating the weighted average of each MIC and dividing by R. This approach improves accuracy in comparison with using the prevalence of resistance to characterize the antimicrobial resistance (AMR) degree of highly resistant strains. For the strains of Salmonella with high AMR, lytic phages were efficiently screened from the phage library by this system, and the lysis spectrum was computed and analyzed. The results showed that the intelligent high-throughput AST/phage screening system was operable, accurate, highly efficient, inexpensive, and easy to maintain. Combined with the Shandong veterinary antimicrobial resistance monitoring system, the system was suitable for scientific research and clinical detection related to AMR.

Introduction

As antimicrobial agents have been widely used to prevent bacterial infectious diseases, antimicrobial resistance (AMR) has become a global public health problem¹. Combating AMR is the current main mission of monitoring AMR of epidemiological pathogens and synergistic therapy of sensitive antimicrobial agents and lytic bacteriophages².

In vitro antimicrobial sensitivity testing (AST) is the mainstay for monitoring therapy and detecting the level of AMR. It is an important part of antimicrobial pharmacology and the critical basis for clinical medication. The Clinical and Laboratory Standards Institute (CLSI) of the United States and the European Committee on Antimicrobial Susceptibility Testing (EUCAST) have formulated and revised international criteria of AST and continuously modified and supplemented AST methods and the breakpoints to determine the MIC of one certain "organism-antimicrobial agent" combination as sensitive (S), resistant (R) or intermediate (I)³^,⁴.

From the 1980s to the 1990s, automatic micro broth dilution instruments were rapidly developed and applied to clinical practice, with examples including Alfred 60AST, VITEK System, PHOENIXTM, and Cobasbact⁵^,⁶^,⁷. However, these instruments were expensive, required high-cost consumables, and their detection ranges were designed for clinical patient medication⁵^,⁶^,⁷. For these reasons, they are not suitable for veterinary clinical examination and detection of large quantities of highly resistant strains. In this study, an intelligent high-throughput AST/phage screening system, including a 96-dot matrix inoculator (Figure 1), image acquisition converter (Figure 2), and corresponding software⁸, was developed to conduct AST for a batch of bacteria strains against multiple antimicrobial agents at one time by the agar dilution method. Moreover, the system was also used to detect and analyze the lysis patterns of phages against antimicrobial-resistant bacteria⁹, and lytic phages were selected efficiently from the phage library. This system was found to be efficient, affordable, and easy to operate.

Figure 1: Structural diagram of the 96-dot matrix inoculator. 1: Inoculation pin plate; 2: Mobile carrier; 3: Seed block; 4: Incubated plate; 5: Base; 6: Operating handle; 7: Limit pin. Please click here to view a larger version of this figure.

Figure 2: Structural diagram of the image acquisition converter. 1: Shell; 2: Display screen; 3: Image acquisition room; 4: Detection board base; 5: Detection board in and out of warehouse; 6: Control board; 7: Image acquisition conversion device; 8: Light source; 9: Image scanner. Please click here to view a larger version of this figure.

Protocol

The Salmonella strains used in this study were collected from poultry in Shandong, China, after obtaining approval from the Biosafety Committee of the Institute of Animal Sciences and Veterinary Medicine, Shandong Academy of Agricultural Sciences, China.

1. Application of the intelligent high-throughput AST system⁸

Inoculum preparation
1. Incubate the quality control organism Escherichia coli and 93 Salmonella strains to be tested for AST on Mueller-Hinton agar (MHA) plates for 16-18 h at 37 °C³.
2. Prepare the inoculum of each strain to match 0.5 McFarland turbidity standard based on the method specified in the CLSI standard³and then dilute 10 times.
3. Place 200 µL of sterile normal saline into the horizontal 1^stwell (A1) of the 96-well plate as the negative control, two suspensions of quality control organism into the horizontal 2^nd and 3^rd wells (A2 and A3) as the positive control, and quality control, respectively. Add 200 µL of the diluted inoculum suspensions of each tested stain into the corresponding 93 wells in the 96-well seed block.
Preparation of antimicrobial agar plate
1. Set the concentration ranges of different antibacterial agents tested according to the calculation range of the Lar index (from 0.125R to 8R). The concentrations range from the quality control range or 0.0625R (subject to the lower range) to 8R.
  NOTE: If the Lar index is not calculated, the range of antibiotic concentrations can be set according to the needs of AST.
2. Execute a log2 doubling dilution scheme for antibiotic solution beginning with a suitable stock concentration based on the agar dilution method specified in the CLSI standard³.
3. Sterilize 50 mL glass bottles containing 18 mL of Mueller-Hinton agar media. Add 2 mL of the appropriate dilutions of the antimicrobial solution to 18 mL of molten media cooled to 45-50 °C, mix thoroughly, and pour into the plates in the biosafety cabinet.
4. Allow the agar to solidify at room temperature (RT), leave a gap under the lid of incubated plates and blow to dry the agar surface before inoculating.
5. Label the types of antimicrobial agents and concentrations on the reverse side of the incubated plates. Arrange the multiple incubated plates of each antimicrobial agent in a stack in log2-doubling dilution order.
6. Prepare two drug-free agar plates as the controls for each antimicrobial agent.
Inoculation steps for 96-dot matrix inoculator
1. Install the autoclaved inoculation pin plate on the support of a 96-dot matrix inoculator in the biosafety cabinet.
2. Place the prepared seed block with tested strains and an agar incubated plate on the mobile carrier, with the same positioning angle for the two plates.
3. Push the mobile carrier so the seed block is directly below the inoculation pin plate.
4. Press the operating handle, move the inoculation pin plate down, and direct the 96 pins to the inocula in 96 wells of the seed block.
5. Release the operating handle with control, then reset the inoculation pin plate under the action of the spring.
6. Press the operating handle 2-3 times to stir each inoculum well and dip. Push and move the carrier plate so the incubated plate is directly below the inoculation pin plate.
7. Press the operating handle, move the inoculation pin plate down, and stop for 1-2 s to make the inoculation pins contact the surface of the incubated plate fully.
8. Release the operating handle. This completes one inoculation. Replace another incubated plate and continue the cycle until one group of antimicrobial agar plates is finished.
9. Replace another inoculation pin plate and seed block, and inoculate another group of tested strains. Cycle until all inoculations are completed.
  NOTE: Inoculate a control agar plate (no antimicrobial agent) first, then the plate in order of drug concentration from low to high, and a second control agar plate last to ensure no contamination or antimicrobial agent carry-over. The inoculating volume relies on the volume of the natural deposition of each pin of approximately 2 µL.
Incubating the antimicrobial agar plates
1. Incubate the inoculated antimicrobial agar plates at RT until the moisture in the inoculum spots is absorbed into the agar.
2. Invert the plates and incubate them for 16-20 h at 37 °C for the tested strains to ensure that the uninhibited bacteria form colonies.
Image acquisition and data statistics
1. Double-click on 96-dot matrix AST image acquisition system to open the program.
2. Click on Test Information in the taskbar. Click on Nuevo to create a new test task, and fill in the information according to the prompts, including the code, name, source, bacteria, number of strains, antibiotics, and gradient.
3. Click on Data Collection > Photograph > Test item to select the new task created. Click on Antibiotics to select the name of the antibiotic, and click on Gradient to select the initial concentration of this antibiotic.
4. Click on Connect to connect with the image acquisition converter.
5. Place the corresponding incubated plates on the detection plate base with the missing angle at the right front for orientation and push into the image acquisition converter.
6. Click on Collection to obtain the images. The antibiotic gradient will automatically jump to the next gradient. Place the next plate in turn and continue to click on Collection until the plates for this antibiotic have been collected.
7. Click on Antibiotics, and select the next set of incubated plates. Click on Gradient to select the starting gradient and proceed to the next round of image collection.
8. After completing all collections, click on Enviar. The program will automatically recognize the number of white pixels formatted at each inoculation point in the images, determine if there is colony formation and convert the images into MIC values.
9. Click on Query to obtain all MIC results of the strains against the tested antibiotics.
  NOTE: The intelligent high throughput AST system is suitable for determining MICs of large batches of bacterial strains. The testing process, including preparation, inoculation, incubation, and result reading, takes 3 days. The types of antibiotics and MIC detection ranges can be set according to respective needs, and the main consumables can be reused.
Calculation of the Lar index
1. Determine the Lar index accurately with the formula: , where:
  MIC_i: minimum inhibitory concentration.
  The range of MIC distributions from MIC_-3 to MIC₃ represents serial twofold concentrations centered on R: 0.125R, 0.25R, 0.5R, R, 2R, 4R, and 8R.
  is 2ⁱ, and the range of i is -3 to 3.
  R: the breakpoints of resistance of bacteria against antimicrobial agents standardized by CLSI.
  f: the MIC frequency distribution.
  NOTE: The general Lar index is the arithmetic mean of all Lar indices. After the Lar index is calculated, round off the final value to two significant digits after the decimal point.

2. Intelligent high-throughput phage screening system⁹

Preparing the phage seed block and double-layer incubated plates containing bacteria.
1. Use the double-layer agar method¹⁰ or liquid culture method¹¹ for making different phages. Dilute to a suitable parallel concentration with a titer of 1 x 10^4-5 pfu/mL, and add 200 µL of the phage inoculum into the 96-well seed block.
2. Make double-layered plates with bacteria (10 mL of bottom agar media [agar 12 g/L] and 6 mL of upper semi-agar media [6 g/L] with 100 µL of bacteria [0.5 McFarland]) to be tested.
3. Make a double-layer incubated plate for each strain to be tested. Leave a gap under the lid of the double-layered plate and blow to dry the agar surface in the biosafety cabinet.
Screening test
1. Place the prepared phage seed block and double-layer plate on the mobile carrier of the 96-dot matrix inoculator, and transfer all phage inocula to the semi-agar surface. Continue the cycles until all tested strains are completed.
2. Let the inoculated double-layer plates remain at RT until the moisture in the inoculum spots is absorbed fully into the semi-agar.
3. Invert the plates and incubate under suitable conditions for the tested strains for 4-6 h to ensure that clear lytic spots are formed.
Analyzing data
1. Obtain and save the image of the experimental result of each double-layer plate by the image acquisition converter (steps 1.5.4-1.5.6).
2. Record the number and morphologies of the different shapes of spots into a spreadsheet based on the obtained images, and calculate the respective proportions of the different kinds of phages.

Representative Results

Following the protocol of the intelligent high-throughput AST system, its application was illustrated by Salmonella from poultry in Shandong, China, as an example.

The growth of Salmonella strains on agar plates with ampicillin (R of 32 µg/mL) at concentrations from 2 to 256 µg/mL determined by the image acquisition converter is shown in Figure 3. The horizontal 1^st well A1 was the negative control and showed no colony growth; A2 and A3 were the quality control strains with MIC 4 µg/mL (forming a colony on the agar plate with 2 µg/mL ampicillin, but not on that of 4 µg/mL), within the quality control range standardized by CLSI (2-8 µg/mL). The MIC of the Salmonella strain in A4 was 64 µg/mL, while that of A5 was 16 µg/mL. MIC distributions of 93 Salmonella strains against ampicillin were calculated automatically by the software.

Figure 3: Morphology of Salmonella on a series of culture plates with ampicillin. 8 horizontal: A-H, 12 vertical: 1-12. Please click here to view a larger version of this figure.

The high-throughput AST system was applied to determine the AMR of Salmonella strains from animals in Shandong Province. The MIC data was uploaded to the database of Varms (http://www.varms.cn/)¹². The statistical results are shown in Table 1. A total of 10 antimicrobial agents were tested against 300-1,500 Salmonella strains, showing the high-throughput advantages of this system.

According to the resistant breakpoints of the CLSI standard, the resistance rate (R%) was calculated as a percentage of strains with MIC ≥ R among the tested strains (Table 1). The R% values of ampicillin, ciprofloxacin, and amoxicillin-clavulanic acid were higher than 50%, the R% values of doxycycline, florfenicol, cefotaxime, and enrofloxacin were 30%-50%, and the R% values of gentamicin, amikacin, and meropenem were less than 30%. Meropenem was not used in industrially raised animals and showed an R% of 7%.

The R% indicated the proportion of the bacterial strains with MICs higher than R, while MIC distributions showed the number of strains with each MIC to describe the overall AMR of Salmonella more accurately. For example, the R% of ampicillin was 73%, and the maximum number of samples (916 strains) was concentrated with MIC ≥ 256 µg/mL, indicating that the resistance of Salmonella to ampicillin was quite serious.

Table 1: MIC distributions, R%, and Lar index values of Salmonella from animals in Shandong Province. MICs corresponding to bold font are the R values of antimicrobial agents. Please click here to download this Table.

For uniformity and comparability, 3 gradients were extended forward and backward, centered on the R of each drug. According to the MIC distributions of seven gradients, the Lar index was calculated by the formula:

.

As an example for ampicillin, the R-value was 32 µg/mL, the number of samples was 1,414, and Lar = (4/32) x (245/1414) + (8/32) × (16/1414) + (16/32) × (117/1414) + (32/32) × (27/1414) + (64/32) × (36/1414) + (128/32) × (57/1414) + (256/32) × (916/1414) = 2^-3 × (245/1414) + 2^-2 × (16/1414) + 2^-1 × (117/1414) + 2⁰ × (27/1414) + 2¹ × (36/1414) + 2² × (57/1414) + 2³ × (916/1414) = 5.48. By this formula, Lar indices of other antimicrobial agents were calculated and are shown in Table 1.

The significance of the Lar index was to indicate the severity degree of AMR accurately. Taking ciprofloxacin and amoxicillin-clavulanic acid as examples, their R% values were similar, at 68% and 65%, respectively, but their Lar indices differed significantly, at 4.57 and 1.76, respectively. The reason for this was clearly illustrated by the distribution of the high MIC values in Table 1, in which 71.3% of ciprofloxacin-resistant strains were distributed in 8R (32 µg/mL), while the MICs of amoxicillin-clavulanic acid-resistant strains were mostly concentrated on R and 2R, and the proportion of 8R was low (8.69%). Therefore, the Lar index of ciprofloxacin was higher than that of amoxicillin-clavulanic acid, indicating that the proportion of highly ciprofloxacin-resistant strains was higher than that of amoxicillin-clavulanic acid-resistant strains. The Lar index was a more accurate indicator of the degree of AMR than the resistance rate.

According to the formula of the Lar index, if the MICs of all strains with respect to a certain drug were R, the Lar index would be 1; if the MICs of all strains were 2R, the Lar index would be 2. Therefore, the Lar index showed multiple relationships between the comprehensive MICs and the corresponding R value, except for the edge concentrations. The Lar index was used to assess the degree of AMR, and the advantage was more pronounced if AMR was higher. For uniformity and comparability, the calculation range of the Lar index was seven MICs with the front and rear 3 gradients centered on the R value, and the weighted average was obtained by integrating the different antimicrobial agents, the number of strains, and MIC distributions. Therefore, the value range of the Lar index was 0.125-8. The closer the Lar was to 0.125, the lower the AMR, and the closer it was to 8, the higher the AMR. However, there was no proportional relationship between Lar and R at the edge concentration. When the antimicrobial agents and the calculation range of the Lar index were definite, the general Lar was normalized to an intuitive comprehensive value used to directly compare and evaluate the degree and change trend of AMR under the different conditions of different bacteria, users, years, regions, etc.

Following the protocol of the intelligent phage screening system, the application was demonstrated by taking 96 phages of Salmonella to lyse AMR Salmonella strains as an example, and the phage lytic pattern was analyzed.

Ninety-six phages were transferred to double-layered plates containing Salmonella by a 96-dot matrix inoculator. The morphology of the formed spots is shown in Figure 4. There were four main types (although not limited to four): clear round spot (●), collection of plaques (), turbid lytic spot (), and no lytic spot (○).

Figure 4: Morphology of Salmonella spots on double-layer agar plates. 1 and 2: the patterns produced by 96 phages on different Salmonella strains. "●" round clear spot, "" collection of plaques, "" turbid lytic spot, "○" no lytic spot) Please click here to view a larger version of this figure.

On the double-layer plates, the lytic spots of different phages on different host bacteria were diverse in morphology¹⁰. The "round clear lytic spot" resulted from a phage that could reliably kill the host on the plate but which may or may not successfully replicate at that host's expense. In this case, further dilution was necessary to conclusively determine the type. The "collection of plaques" was formed by true plaques. Each individual zone of lysis was clearly produced from a single infectious center, which demonstrated that the phage had replicated at the expense of the bacteria on the plate. The "turbid lytic spot" resulted from a phage that did not reliably kill the host on the plate and which may or may not successfully replicate at that host's expense. In this case, there was more than one possibility, thus requiring confirmation based on further research interests. The "no lytic spot" indicated nonlytic nature.

Moreover, using this system for preliminary testing could essentially determine whether the strains and bacteriophages were duplicated. If different Salmonella species were selected and the patterns of two bacteriophages were identical, it indicated that the bacteriophages might be duplicated. If nonrepetitive bacteriophages were selected to infect unknown Salmonella species from clinical sources and the phage pattern was the same, it indicated that Salmonella strains might be the same strain. Furthermore, the number and proportion of duplicates had reference values for epidemiological investigation.

Discussion

The agar dilution method has been well-established and used widely. The principle of the high-throughput AST system was that of the agar dilution method. One of the critical steps within the protocol was the accurate high throughput transfer of 96 inocula at one time, which was performed multiple times in a row. To complete this critical step, the pins of the 96-dot matrix inoculator were uniform and very smooth. The natural deposition of each pin was a volume of approximately 2 µL, which aggregated into small droplets on the surface of the agar media to be quickly absorbed into the agar, not flowing or splashing to cause cross-contamination. The second critical step was the statistical processing of large AST data. With high-throughput inoculation, test data needed to be determined, and the workload was huge. The intelligent analysis and statistical results produced by the intelligent image acquisition converter and supporting software were a perfect solution to this problem. The AST results were automatically uploaded directly to the Varms database. The efficiency and accuracy of result interpretation were improved, and the errors caused by human factors were reduced¹³.

The third critical step was to propose the Lar index of AMR. At present, there are few comprehensive evaluation indices of AMR in the world. According to the literature, a drug resistance index (DRI) was described by Laxminarayan and Klugman to measure changes in antibiotic effectiveness¹⁴^,¹⁵. It combined the prevalence of resistance and relative frequencies of prescription but could not characterize the degree of AMR and evaluate the changes in high drug resistance levels. The drug effectiveness index (DEI)¹⁶, another index derived from the DRI, has the same disadvantage as the DRI. Thus, the Lar index was proposed, which consisted of three steps: (1) The MICs of bacterial strains were normalized based on the respective R-value, eliminating the differences in antimicrobial agents caused by different R values of the AST standard; (2) According to the MIC distributions, the weighted average values were calculated to reflect the degree of AMR more accurately than the resistance rate; (3) The arithmetic mean of Lar indices of multiple antimicrobial agents, that is, the general Lar, could reflect the comprehensive situation of AMR, offering convenience for the assessment and comparison of AMR at different levels.

The hardware design of these apparatuses was reasonable and simple to operate, and all parts ran smoothly. There was no jamming problem or fault. The design of the supporting software matched the personalized requirements of AST and phage screening and was easy to operate and use. One instrument was equipped with 4-5 boxes of inoculation pins for multiple applicable scenarios of batch bacterial transfer. The core components of this instrument were the inoculation pin plate and pins made of stainless steel, which were adaptable to a variety of environments and were able to be autoclaved, disassembled and replaced. The inoculation pins were designed to be combined in any way.

It was imperative to establish an AMR monitoring system because of the prevalence of resistant pathogens caused by the misuse of antibiotics. Since 2008, the public health team of the Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences, has carried out AMR monitoring of animals successively in Shandong Province¹²^,¹³^,¹⁷. It was necessary to efficiently detect MICs of pathogens to regulate the use of antimicrobial agents because of the high level of veterinary resistance and the large monitoring volume. However, the relevant instruments for AST are expensive, and the cost of the operation and consumables is high and not suitable for a wide range of large-scale farms. For this reason, the development of the intelligent high-throughput AST system and the standardization of its application were conducive to promoting the establishment of a sound system for AMR monitoring technology. According to previous research¹²^,¹³, the intelligent high-throughput AST system achieved good repeatability and stability to match the standard of CLSI and was applied to AST and analysis of clinical pathogenic bacteria in animals. To date, comprehensive AMR data for more than 20,000 epidemic strains have been accumulated¹². For the resistant bacteria found in the monitoring process, this system could also be used for rapid high-throughput screening of lytic phages to cooperate with antimicrobial agents to reduce AMR. The application of the 96-dot matrix inoculator and the image acquisition converter for phage lysis screening was an extended function, and no other instruments had previously been applied in this field.

The intelligent high-throughput AST/phage screening system combined AST with lytic bacteriophages to achieve AMR monitoring, control, and reduction. At the same time, the Lar index was more intuitively and concisely used to evaluate the contributions of various factors and new antibacterial technologies to the reduction of AMR.

Divulgaciones

The authors have nothing to disclose.

Acknowledgements

This work was supported by the National Key Research and Development Project (2019YFA0904003); Modern Agricultural Industrial System in Shandong Province (SDAIT-011-09); International Cooperation Platform Optimization Project (CXGC2023G15); Major Innovation tasks of agricultural Science and technology innovation project of Academy of Agricultural Sciences Shandong, China (CXGC2023G03).

Materials

96 well culture plate	Beijing lanjieke Technology Co., Ltd	11510
96-dot matrix AST image acquisition system	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	In-house software copyright
96-dot matrix inoculator	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	N/A	Patented product
Agar	Qingdao hi tech Industrial Park Haibo Biotechnology Co., Ltd	HB8274-1
Amikacin	Shanghai McLean Biochemical Technology Co., Ltd	A857053
Amoxicillin	Shanghai McLean Biochemical Technology Co., Ltd	A822839
Ampicillin	Shanghai McLean Biochemical Technology Co., Ltd	A830931
Analytical balance	Sartorius	BSA224S
Automated calculation software for Lar index of AMR	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	In-house software copyright
Bacteria Salmonella strains	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	N/A	Animal origin
Bacterial resistance Lar index certification management system V1.0	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	In-house software copyright
Ceftiofur	Shanghai McLean Biochemical Technology Co., Ltd	C873619
Ciprofloxacin	Shanghai McLean Biochemical Technology Co., Ltd	C824343
Clavulanic acid	Shanghai McLean Biochemical Technology Co., Ltd	C824181
Clean worktable	Suzhou purification equipment Co., Ltd	SW-CJ-2D
Colistin sulfate	Shanghai McLean Biochemical Technology Co., Ltd	C805491
Culture plate	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	N/A	Patented product
Doxycycline	Shanghai McLean Biochemical Technology Co., Ltd	D832390
Enrofloxacin	Shanghai McLean Biochemical Technology Co., Ltd	E809130
Filter 0.22 μm	Millipore	SLGP033RB
Florfenicol	Shanghai McLean Biochemical Technology Co., Ltd	F809685
Gentamicin	Shanghai McLean Biochemical Technology Co., Ltd	G810322
Glass bottle 50 mL	Xuzhou Qianxing Glass Technology Co., Ltd	QX-7
High-throughput resistance detection system V1.0	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	In-house software copyright
Image acquisition converter	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	N/A	Patented product
Meropenem	Shanghai McLean Biochemical Technology Co., Ltd	M861173
Mueller-Hinton agar	Qingdao hi tech Industrial Park Haibo Biotechnology Co., Ltd	HB6232
Petri dish 60 mm x 15 mm	Qingdao Jindian biochemical equipment Co., Ltd	16021-1
Petri dish 90 mm x 15 mm	Qingdao Jindian biochemical equipment Co., Ltd	16001-1
Salmonella phages	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	N/A
Shaker incubator	Shanghai Minquan Instrument Co., Ltd	MQD-S2R
Turbidimeter	Shanghai XingBai Biotechnology Co., Ltd	F-TC2015
Varms base type library system V1.0	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	In-house software copyright
Vertical high-pressure steam sterilizer	Shanghai Shen'an medical instrument factory	LDZX-75L
Veterinary pathogen resistance testing management system	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	In-house software copyright
Veterinary resistance cloud monitoring and phage control platform V1.0	Institute of Animal Science and Veterinary Medicine, Shandong Academy of Agricultural Sciences	In-house software copyright

Referencias

Ramanan, L., et al. Antimicrobial resistance-the need for global solutions. The Lancet Infectious Diseases. 13 (12), 1057-1098 (2013).
Xiaonan, Z., Qing, Z., Thomas, S. P., Yuqing, L., Martha, R. J. C. inPhocus: Perspectives of the application of bacteriophages in poultry and aquaculture industries based on Varms in China. PHAGE: Therapy, Applications, and Research. 2 (2), 69-74 (2021).
CLSI. . Performance Standards for Antimicrobial Disk Susceptibility Tests. CLSI document M100. , (2022).
Yuqing, L., et al. . Antimicrobial Sensitivity Testing Standard of EUCAST. , (2017).
Barnini, S., et al. A new rapid method for direct antimicrobial susceptibility testing of bacteria from positive blood cultures. BMC Microbiology. 16 (1), 185-192 (2016).
Höring, S., Massarani, A. S., Löffler, B., Rödel, J. Rapid antimicrobial susceptibility testing in blood culture diagnostics performed by direct inoculation using the VITEK®-2 and BD PhoenixTM platforms. European Journal of Clinical Microbiology & Infectious Diseases. 38 (3), 471-478 (2019).
Dupuis, G. Evaluation of the Cobasbact automated antimicrobial susceptibility testing system. European Journal of Clinical Microbiology & Infectious Diseases. 4 (2), 119-122 (1985).
Liu, Y., et al. A system of bacterial antimicrobial resistance detection and its operation method. China Patent. , (2019).
Liu, Y. A high throughput test plate for screening bacteriophage of zoonotic pathogens and its application. China Patent. , (2022).
Adams, M. H. . Bacteriophages. , (1959).
Nair, A., Ghugare, G. S., Khairnar, K. An appraisal of bacteriophage isolation techniques from environment. Microbial Ecology. 83 (3), 519-535 (2022).
. . Shandong veterinary antibiotic resistance system. , (2023).
Ming, H., et al. Comparison of the results of 96-dot agar dilution method and broth microdilution method. Chinese Journal of Antibiotics. 43 (6), 729-733 (2018).
Laxminarayan, R., Klugman, K. P. Communicating trends in resistance using a drug resistance index. BMJ Open. 1 (2), e000135 (2011).
Chen, Y., et al. Assessing antibiotic therapy effectiveness against the major bacterial pathogens in a hospital using an integrated index. Future Microbiology. 12, 853-866 (2017).
Ciccolini, M., Spoorenberg, V., Geerlings, S. E., Prins, J. M., Grundmann, H. Using an index-based approach to assess the population-level appropriateness of empirical antibiotic therapy. Journal of Antimicrobial Chemotherapy. 70 (1), 286-293 (2015).
Yanbo, L., et al. Preliminary application of inoculation system for high-throughput drug susceptibility test. China Poultry. 42 (6), 52-57 (2020).

Play Video

PDF

DOI

DOWNLOAD MATERIALS LIST

Citar este artículo

Hu, M., Liu, Z., Song, Z., Li, L., Zhao, X., Luo, Y., Zhang, Q., Chen, Y., Xu, X., Dong, Y., Hrabchenko, N., Zhang, W., Liu, Y. Application of the Intelligent High-Throughput Antimicrobial Sensitivity Testing/Phage Screening System and Lar Index of Antimicrobial Resistance. J. Vis. Exp. (197), e64785, doi:10.3791/64785 (2023).