Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization

1. Photon-active Blend Ink Preparation

1. Weigh 10 mg of DPPBT polymer and 10 mg of PC₇₁BM material (chemical structures shown in Figure 1). Mix them in a 4 ml vial.
2. Add 1.5 ml chloroform and 75 µl of 1,2-dichlorobenzene into the mixture.
3. Put a small stir bar into the vial, close the vial with a polytetrafluoroethylene (PTFE) cap, and transfer the vial to a hot plate. Stir at ~400 rpm, and heat at ~50 °C overnight before use.

2. ITO and Wafer Substrate Cleaning and Preparation

1. Load pre-patterned indium tin oxide (ITO) glass substrate (1 inch by 3 inches, with half removed ITO) or silicon wafer into a Teflon cleaning rack and put the rack into a glass container (Figure 2). Add dilute detergent solution (300 ml, 1% universal detergent solution) into the glass container and put the glass container into sonicator and sonicate for 15 min.
2. Remove the detergent and rinse the ITO glass with deionized (DI) water a couple of times. Then add 300 ml DI water into the container, and put the glass container into sonicator for another 15 minutes.
3. Remove the water from the container. Add 300 ml acetone into the container, and sonicate for 15 min.
4. Remove the acetone. Add 300 ml 2-isopranol into the glass container, and then sonicate for 15 min.
5. Move the cleaning rack out into an oven. Set the oven temperature to 100 °C, and wait 3-5 hr until the ITO glass is completely dried.
6. Take out cleaned substrates. Transfer them into an UV-ozone cleaner or oxygen plasma cleaner. Use high-powered UV-ozone or plasma to clean them for ~15 min according to manufacturer's protocol.
7. Put the cleaned substrate onto a spin-coater, add 150 µl poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) solution onto the cleaned substrate, and spin coat at 3,000 rpm to coat a ~30 nm thick PEDOT:PSS (PEDOT:PSS 4083) thin film onto either the ITO glass or silicon wafers.
8. Take off spin coated substrates. Transfer the fresh coated substrates onto a heating plate and anneal at 150 °C for 15 min.

3. Active Layer Printing

1. Load substrate. Put the PEDOT:PSS coated ITO substrate onto the base plate of mini slot die coater. Turn on the vacuum pump that is connected to the vacuum chuck of the slot die coater to hold the substrate tightly. (See Figure 3 to locate different components.)
2. Adjust the position of substrate to put it right beneath printer head. This can be done by using the linear manipulator beneath the substrate plate.
3. Adjust the head tilting using the 2-D tilting manipulator that holds the printing head. Make sure that the head stands vertically on top of the loaded substrate. Note that in this process, the printing head can be lowered close to the substrate. Use the gap between printing head and substrate to show whether the head is tilted or not. This will be extremely useful when a wafer substrate is used, since a minor image of printing head will show up and it will be much easier to check the tilting.
4. Tune the head-to-substrate distance to zero. The vertical motor is coupled with a force sensor. When the printing head is floating, a constant force reading will be obtained (from the weight of printing head and tilting manipulator assemblies). Once printer head touches substrate, the reading will reduce, marking the zero position. See Figure 4 for the step distance setting. Use jog mode in tuning the distance.
   NOTE: The vertical manipulator translational plate is connected to its base using springs and the spring constant varies slightly. Thus small changes in force sensor are inevitable during the experiment.
5. Set a head-to-substrate value to run the experiment. In this experiment, set the head to substrate gap to 100 µm.
6. Adjust the linear translational stage motor that will be used to print. Find the starting point and end point. Record these values. The travel distance of the linear motor is 100 mm. Here, set 10 mm motor position as the starting point and 80 mm motor position as the end point.
7. Set the printing speed to 10 mm/sec by using the motor controlling software interface (Figure 4b). Set the motor acceleration speed to 100 m/sec.
   1. If the motor does not work properly or the software has an error, please restart the software and click "enable" and then "home" in the software interface. Note that during printing process, the printing head remains fixed and the substrate moves to dispense the solution and mimic the industrial printing process.
8. Load DPPBT:PCBM solution (room temperature) into 1 ml syringe and mount the syringe to the syringe pump that is connected to the slot die printer. Set the printing parameters in controlling software (syringe diameter and solution feeding speed, 0.3 ml/min in this case).
9. Start the printing experiment.
   1. Move the substrate to the starting point by typing the starting point position in the position window in controlling software. See Figure 4c for details.
   2. Start to pump solution into slot die head by clicking the start in the syringe pump software. Alternatively, manually operate the syringe pump. For each coating, around ~100 µl of solution will be used. Normally, use 300 µl solution for first time printing and use ~100 µl solution for repeated printing.
   3. Quickly start the translational motor when the solution starts coming out from the printing head, and the substrate will move to the end position. Please note this is a critical step. Preload the translational motor ending position into the position window, and click enter to start the motor movement.
   4. Stop the syringe pump and lift the printing head by using the vertical motor. Turn the vacuum off and take the substrate off the base plate. Note that the dead volume for this printing head is 250 µl, and thus filling the first time takes more than 250 µl of solution.
   5. Load the printed substrate into a vacuum oven for 3-5 hr to remove residual solvent.
   6. Put a Petri dish beneath the printing head. Pump 10 ml chloroform into the printing head to clean the head. Collect the contaminated chloroform solution with the Petri dish. Use cotton swabs to clean the printing head while pumping the cleaning solution. After each coating run, clean the printing head, especially when a different solution is used.
      NOTE: The DPPBT:PCBM solution shows a dark green color. When the cleaning is complete, no color can be seen from the chloroform solvent.

4. Cathode Electrode Deposition

1. Load the active layer coated substrate onto shadow masks (Figure 5) and mount the mask into the evaporation chamber.
2. Put two thermal evaporation boats in between the electrode studs (Figure 6a). Load one boat with LiF salt (barely covering the boat, ~0.2 g) and one boat with aluminum metal (4 pellets).
3. Close the evaporation chamber and pump down the evaporation chamber to about 2 x 10^-6 Torr.
4. Set the chamber to deposit 1 nm of LiF followed by 100 nm of aluminum. In the current case, use 20% power for LiF deposition and use 26% power for Al deposition. Shown in Figure 6b is the evaporator control interface of the system used in this study.
5. Stop evacuation pumps and fill the chamber with nitrogen gas. When pressure returns to atmosphere pressure, take the substrates out.

5. Photovoltaic Performance Measurement

1. Prepare a glass slide that is half the width of the ITO glass that is used in device fabrication. Carry out this step in a glove box. Paste epoxy glue to one side of the glass substrate, and cover the device area using the epoxy glue coated glass slides (see Figure 11 for sample device). When the epoxy has cured, the device will be fully sealed.
2. Start the solar simulation lamp and set to AM 1.5 radiation with 100 mW/cm². Stabilize the lamp for about 15 min before measurement. Shown in Figure 7 is the PV measurement system used in this study.
3. Mount the device under the solar simulator at the instrument suggested distance. Connect the anode and the cathode to the measurement circuit. Record a current-voltage curve using an electrical multimeter using manufacturer's protocol.
4. Determine the performance of the device as follows:
   J_sc: short circuit current, the maximum current that a solar cell device can deliver;
   V_oc: open circuit voltage, the maximum voltage that a solar cell device can deliver;
   FF: fill factor, the maximum area in I-V curve divided by J_sc* V_oc;
   PCE: power conversion efficiency, J_sc* V_oc*FF/(100mW/cm²).

6. Synchrotron X-ray Measurement

1. Set up a helium box to suppress air scattering in the X-ray measurement. Mount the mini-slot die coater into the helium box. Shown in Figure 8 is the experiment setup of grazing incidence X-ray diffraction experiments using a helium box at Advanced Light Source.
2. Mount an optical interferometer onto the printing machine to monitor the thickness change over the solvent evaporation. In this experiment, use an UVX model (e.g., Filmetrix F20). The materials that are used in this experiment have strong light absorption from 300-900 nm wavelength.
   1. Use a source lamp of optical interferometer that avoids material absorption. Use an 1,100-1,700 nm wavelength lamp in this experiment. Pre-calibrate the instrument before experiment following its operation procedures.
3. Put the PEDOT:PSS coated wafer substrate onto substrate holder of the printer and adjust the head and substrate position following step 3.2-3.5. Turn on the vacuum pump and make sure that the wafer substrate sticks to the substrate holder tightly.
4. Purge the helium box to remove air. Note that oxygen level should be less than 0.3 v%, which can be monitored by oxygen sensor.
5. Align the substrate at the position where the X-ray impinges on the substrate (the end position in printing), and set the incidence angle, 0.16° in this case. Align according to beam-line protocol.
6. Set the X-ray exposure time and data acquisition method. Here, use 2 sec as the exposure time, and followed by 3 sec of delay time (to avoid server beam damage). Thus each experiment period will be 5 sec. Carry out a continuous queue of 100 repeats; thus take 100 pictures.
7. Name the experiment and choose the data path to save experimental files. Shown in Figure 9 is the Advanced Light Source beamline 7.3.3 user interface where the above-mentioned settings can be easily located.
8. Move the substrate to the starting position by entering the starting position in motor controlling software. Start the X-ray shutter and the detector will continuously record diffraction/scattering signals.
9. Start the syringe pump to feed solution into printing head. When the solution begins to eject from the printing head (monitored by a surveillance camera), quickly start the printing process.
   NOTE: When the pre-chosen measurement position is reached, 2-D detector will capture the scattering signal from solution. Film thickness will be monitored by interferometer. Thus the thin film morphology evolution will be recorded.
10. Lift up the printer head and clean the head when experiment is done.