Sonication Extraction of Lipid Biomarkers from Sediment
7,111 Views
•
•
概述
Source: Laboratory of Jeff Salacup - University of Massachusetts Amherst
The material comprising the living "organic" share of any ecosystem (leaves, fungi, bark, tissue; Figure 1) differs fundamentally from the material of the non-living "inorganic" share (rocks and their constituent minerals, oxygen, water, metals). Organic material contains carbon linked to a series of other carbon and hydrogen molecules (Figure 2), which distinguishes it from inorganic material. Carbon's wide valency range (-4 to +4) allows it to form up to four separate covalent bonds with neighboring atoms, usually C, H, O, N, S, and P. It can also share up to three covalent bonds with a single other atom, such as the triple bond in the often-poisonous cyanide, or nitrile, group. Over the past 4.6 billion years, this flexibility has led to an amazing array of chemical structures, which vary in size, complexity, polarity, shape, and function. The scientific field of organic geochemistry is concerned with the identification and characterization of the whole range of detectable organic compounds, called biomarkers, produced by life on this planet, as well as others, through geologic time.
Figure 1. Organic material, such as trees, leaves, and moss, are chemically and visually distinct from inorganic material, such as pavement.
Principles
Extraction via sonication is the simplest and least expensive method of obtaining a total lipid extract (TLE) from a given sample, and the recovery associated with this method is on par with other more sophisticated techniques. It uses an ultrasonic bath to agitate a sample in a vial in the presence of organic solvent. Biomarkers contained in the sample dissolve into the organic phase based on the rules of solubility, which with organic compounds, are controlled primarily by the polarity of both the biomarker and the solvent. This is summarized by the so-called ‘like dissolves like’ rule, whereby relatively apolar biomarkers (those containing exclusively C and H; isoprene) dissolve in apolar solvents (such as hexane, polarity = 0.1) and more polar biomarkers (those containing O, N, S, P; glycerol-dialkyl glycerol-tetraethers (GDGT’s)) dissolve in more polar solvents (such as methanol or dichloromethane, polarity = 5.1 and 3.1). In fact, this is the first step in which the separation of different groups of biomarkers can be achieved via the introduction of a series of solvents, from apolar to polar, each extracting ever more polar compounds from the sample. The solvents from sequential extracts of a target sediment can thus be analyzed separately or combined to form a total lipid extract (TLE) that can be purified later.
The first step in paleoclimatology is to collect, or extract, the biomarkers from the sediment they are found in. Environmental samples are composed of non-organic components, such as minerals, water, and metals, and organic components that are created by living organisms in the area. Before these organic components can be used by scientists to elucidate information about the past, they must be removed from their environment. Sonication, which utilizes ultrasonic waves, is the simplest and least expensive of these techniques.
This video is part of a series on lipid extraction, purification, and analysis from sediments. It will illustrate lipid extraction by ultrasound and present a few applications of the method.
Because of the wide range of biomarkers, there is no single solvent optimized to extract all of them. This is summarized by the so-called ‘like dissolves like’ rule, whereby relatively apolar molecules dissolve in apolar solvents such as dichloromethane, and more polar molecules dissolve in more polar solvents such as methanol. Solvent mixtures for the extraction of specific lipids or groups of lipids are generally optimized empirically.
To accelerate extraction and increase yield, a sonication system is used to apply ultrasound – waves with frequencies greater than 20 kHz, in conjunction with the solvent mixture. When these waves contact the liquid organic phase, they cause the formation of short-lived microbubbles of solvent vapors that rapidly grow and collapse. On collapsing, these bubbles release a tremendous amount of energy as mechanical shear, facilitating lipid solubilization and dramatically increasing the efficiency of extraction.
After the ultrasound assisted solvent-extraction process, the result is a crude extract preparation, called a total lipid extract, that is subjected to further purification to allow qualitative and quantitative examination of lipid signatures. Now that you understand some of the main principles behind lipid extraction by sonication, lets take a look at a protocol for how the procedure is performed.
Collect the necessary sample materials from a chosen location. Some examples are lacustrine and marine sediments, terrestrial soils, microbial cultures, or plant leaves. Collected material is frozen overnight. Following this it is freeze-dried in a freeze dryer for 2 to 3 days. Crush and homogenize the freeze-dried samples prior to extraction with a solvent-rinsed mortar and pestle. To remove organic contaminants, combust the required borosilicate glass pipettes, vials, and weighing tins in an oven. After allowing the glassware to cool in the oven, rinse the metal tools with a mixture of dichloromethane and methanol. Once the sample and glassware are prepared, the sonication procedure can begin.
From this step on, all containers and glassware should be combusted before use. Place the weighing tin on a scale and tare. Rinse the lab spatula with the solvent mixture, then, use it to transfer an appropriate mass of freeze-dried, homogenized sample into the weighing tin and record the mass. Carefully transfer the weighed sample into a labeled vial. Using the squirt bottle of DCM:MeOH, add enough that the sample is covered by 1 to 2 cm of solvent, and cap the vial. Place the vial on a waterproof rack, now ready for sonication. Place the rack directly into the sonication bath. Check that the water level in the sonication bath is just deep enough to submerge the sample vials up to the top of the extraction solvent. Sonicate for 30 minutes at room temperature. After sonication, remove the rack from the sonicator. Let the vials sit to allow sediment settling to occur.
Remove the dichloromethane-methanol upper phase from the extraction vial using a pipette and bulb, and transfer into another pre-weighed and labeled vial. Repeat the sonication process a total of three times for each sample. Collect the extracts into one vial. Allow extracted samples to dry in their vials, caps off, and in the hood, covered loosely with a piece of foil. Label as ‘extracted residue’ and store in the extraction solvent. Now that the biomarkers have been extracted, they must be purified before analysis can take place.
Sonication accelerates several solvent extraction processes and is widely used in geochemical studies. Many archeologists work with geochemists in order to reconstruct the environmental and cultural circumstances under which early human civilizations lived. Pottery, one of the oldest human inventions, when unearthed, can be found to contain residual molecular fossils from wine, rice, or other contents that were once stored within.
To unearth chemical evidence of substances absorbed onto the surfaces, small samples of pottery are sonicated in the presence of organic solvents and extracted compounds can be subsequently identified downstream by spectroscopic methods. This kind of analysis helps archeologists detect the kinds of resources that were available to ancient populations and reconstruct the conditions of their habitat.
Photosynthetic microalgae are found in marine and freshwater ecosystems. Because they grow in seawater-based media and their culture occupies significantly smaller areas, they are now being widely studied as a promising alternative to terrestrial plants for the production of biofuels.
To extract lipids from a microalgal biomass, these researchers describe a sonication-assisted solvent extraction. Acoustic cavitation during sonication effectively disrupts rigid microalgal cell walls in order to liberate lipids. Such techniques aid the characterization of new microalgae from the environment for the production of non-petroleum sources of energy.
You’ve just watched JoVE’s introduction to Sonication-Assisted Extraction of Biomarkers from Sediments. The following videos will explain how the extract is further purified for analysis.
Thanks for watching!
Procedure
1. Collect the Necessary Materials
- Samples (leaves, dirt, fungi, bark, tissue), usually frozen, freeze-dried, crushed, and homogenized prior to extraction, extracted in groups to maximize efficiency. Extract three samples.
- Depending on the size of the sample, vials with volumes ranging from 4-60 mL may be used. For this experiment, borosilicate glass vials (40 mL) and solvent safe caps are used. Vials, borosilicate glass pipettes, and weighing tins should be combusted at 550 °C for 6 h prior to ensure removal of possible organic contaminants.
- Dichloromethane and methanol are common in most organic geochemistry laboratories. They are used individually to rinse lab tools and glassware before use. A mixture of dichloromethane (DCM) to methanol (MeOH; 9:1) is used in many labs to efficiently extract biomarkers with a wide range of polarities. Solvents should be free of organic contaminants.
- Use a sonication water bath at room temperature. A range of sonicator sizes and sonication with or without heat are available from major scientific equipment retailers.
- Vial racks, which should be waterproof, will be placed in sonication bath.
- Solvent approved chemical hood.
2. Preparation of Sample
- Place a combusted weighing tin on the lab scale and then tare.
- Rinse the lab spatula with solvent, then use it to transfer an appropriate mass of sample into the weighing tin, and record the mass.
- The mass of the sample varies depending on its organic matter content. Relatively organic matter lean material (marine mud) may require several grams, while organic matter rich material (leaf tissue) may require much less.
- Transfer all of the material in the weighing tin into a combusted, pre-weighed, and labelled vial. Cap the vial, then discard the weighing tin.
- Perform steps 2.1 – 2.3 for each sample to be extracted.
3. Extraction
- Using a pre-combusted pipette and bulb, transfer ~20 mL of the DCM:MeOH (9:1) mixture into each vial (vial should be approximately half full). Recap vials before moving on to next sample, so the volatile solvents do not evaporate.
- The volatilities of DCM and MeOH are different. Evaporation of extraction solvent due to uncapped sample vials has the ability to change its polarity, and thus the extraction.
- Place the sample vials into a waterproof vial rack.
- Check that the level of water in the sonication bath is only deep enough to submerge the sample vials up to the top of the extraction solvent. Too much water may cause the vials to float; too little water may stop the samples from being properly agitated.
- Place the vial rack with the samples in it directly into the sonication bath.
- Sonicate for 30 min at room temperature.
- Remove sample rack from sonicator. If extracting sediments, let it set for 30 min to allow settling to occur. If extracting another set of samples, put in sonicator at this time.
- Remove the DCM:MeOH mixture from the extraction vial, using a pre-combusted pipette and bulb, and insert into another pre-weighed, pre-combusted, and labeled 40-mL vial.
- Repeat 3.1 – 3.7 3x for all samples.
- Allow extracted samples to dry in their vials, caps off, and in the hood, covered loosely with a piece of foil. Label as 'extracted residue' and store.
- Label the combined extracts for each sample as 'TLE'.
The first step in paleoclimatology is to collect, or extract, the biomarkers from the sediment they are found in. Environmental samples are composed of non-organic components, such as minerals, water, and metals, and organic components that are created by living organisms in the area. Before these organic components can be used by scientists to elucidate information about the past, they must be removed from their environment. Sonication, which utilizes ultrasonic waves, is the simplest and least expensive of these techniques.
This video is part of a series on lipid extraction, purification, and analysis from sediments. It will illustrate lipid extraction by ultrasound and present a few applications of the method.
Because of the wide range of biomarkers, there is no single solvent optimized to extract all of them. This is summarized by the so-called 'like dissolves like' rule, whereby relatively apolar molecules dissolve in apolar solvents such as dichloromethane, and more polar molecules dissolve in more polar solvents such as methanol. Solvent mixtures for the extraction of specific lipids or groups of lipids are generally optimized empirically.
To accelerate extraction and increase yield, a sonication system is used to apply ultrasound – waves with frequencies greater than 20 kHz, in conjunction with the solvent mixture. When these waves contact the liquid organic phase, they cause the formation of short-lived microbubbles of solvent vapors that rapidly grow and collapse. On collapsing, these bubbles release a tremendous amount of energy as mechanical shear, facilitating lipid solubilization and dramatically increasing the efficiency of extraction.
After the ultrasound assisted solvent-extraction process, the result is a crude extract preparation, called a total lipid extract, that is subjected to further purification to allow qualitative and quantitative examination of lipid signatures. Now that you understand some of the main principles behind lipid extraction by sonication, lets take a look at a protocol for how the procedure is performed.
Collect the necessary sample materials from a chosen location. Some examples are lacustrine and marine sediments, terrestrial soils, microbial cultures, or plant leaves. Collected material is frozen overnight. Following this it is freeze-dried in a freeze dryer for 2 to 3 days. Crush and homogenize the freeze-dried samples prior to extraction with a solvent-rinsed mortar and pestle. To remove organic contaminants, combust the required borosilicate glass pipettes, vials, and weighing tins in an oven. After allowing the glassware to cool in the oven, rinse the metal tools with a mixture of dichloromethane and methanol. Once the sample and glassware are prepared, the sonication procedure can begin.
From this step on, all containers and glassware should be combusted before use. Place the weighing tin on a scale and tare. Rinse the lab spatula with the solvent mixture, then, use it to transfer an appropriate mass of freeze-dried, homogenized sample into the weighing tin and record the mass. Carefully transfer the weighed sample into a labeled vial. Using the squirt bottle of DCM:MeOH, add enough that the sample is covered by 1 to 2 cm of solvent, and cap the vial. Place the vial on a waterproof rack, now ready for sonication. Place the rack directly into the sonication bath. Check that the water level in the sonication bath is just deep enough to submerge the sample vials up to the top of the extraction solvent. Sonicate for 30 minutes at room temperature. After sonication, remove the rack from the sonicator. Let the vials sit to allow sediment settling to occur.
Remove the dichloromethane-methanol upper phase from the extraction vial using a pipette and bulb, and transfer into another pre-weighed and labeled vial. Repeat the sonication process a total of three times for each sample. Collect the extracts into one vial. Allow extracted samples to dry in their vials, caps off, and in the hood, covered loosely with a piece of foil. Label as 'extracted residue' and store in the extraction solvent. Now that the biomarkers have been extracted, they must be purified before analysis can take place.
Sonication accelerates several solvent extraction processes and is widely used in geochemical studies. Many archeologists work with geochemists in order to reconstruct the environmental and cultural circumstances under which early human civilizations lived. Pottery, one of the oldest human inventions, when unearthed, can be found to contain residual molecular fossils from wine, rice, or other contents that were once stored within.
To unearth chemical evidence of substances absorbed onto the surfaces, small samples of pottery are sonicated in the presence of organic solvents and extracted compounds can be subsequently identified downstream by spectroscopic methods. This kind of analysis helps archeologists detect the kinds of resources that were available to ancient populations and reconstruct the conditions of their habitat.
Photosynthetic microalgae are found in marine and freshwater ecosystems. Because they grow in seawater-based media and their culture occupies significantly smaller areas, they are now being widely studied as a promising alternative to terrestrial plants for the production of biofuels.
To extract lipids from a microalgal biomass, these researchers describe a sonication-assisted solvent extraction. Acoustic cavitation during sonication effectively disrupts rigid microalgal cell walls in order to liberate lipids. Such techniques aid the characterization of new microalgae from the environment for the production of non-petroleum sources of energy.
You've just watched JoVE's introduction to Sonication-Assisted Extraction of Biomarkers from Sediments. The following videos will explain how the extract is further purified for analysis.
Thanks for watching!
Results
At the end of extraction, a total lipid extract (TLE) for each sample is evident. Each vial contains the extractable organic matter from a sediment, soil, or plant tissue. These TLEs can now be analyzed and their chemical constituents identified and quantified.
Applications and Summary
Different classes of biomarkers impart information on specific aspects of the Earth system. For example, in its infancy, organic geochemistry was primarily concerned with the formation, migration, and alteration of petroleum, and many of the chemical tools organic geochemists use today are based on those initial investigations. It was through the investigation of a class of compounds called isoprenoids, having a repeating five carbon pattern (Figure 2), that scientists discovered petroleum comprised the chemically altered remains of ancient primary producers, such as plankton in the ocean (converting to oil, Figure 3) or peat bogs on land (coal, Figure 4). Chemists at large oil companies used the ratios of a variety of compounds, each with its own known rate of alteration, to estimate how old petroleum was, where it came from, and if it was worth exploiting. Today, new biomarkers are being discovered, identified, and characterized in modern and ancient samples analyzed in organic geochemistry labs around the world. Many of today's applications seek to extract environmental information from biomarkers obtained in modern samples (leaves, soil, microbes, water samples, etc.) in order to extend the biomarker's utility to ancient sediments in an effort to reconstruct the climates, environments, and ecosystems of the past. For example, the distribution of a group of biomarkers called glycerol-dialkyl glycerol-tetraethers (GDGTs for short), produced by a suite of archaea and bacteria, were found in modern sediments to change in a predictable manner in response to air or water temperature. Therefore the distribution of these biomarkers in ancient sediments can be used, or through a series of sediments of known age, to reconstruct air and water temperature back several million years.
Figure 2. Isoprene comprises five carbon atoms and two double bonds. When added together in biosynthesis reaction, they can form complex molecules diagnostic for the presence of life. For example, 2, 6,10,15,19-pentamethyleicosane, commonly found in cyanobacterial mats.
Figure 3. Illumination of plankton at Maldives. Copyright PawelG Photo.
Figure 4. Peat bog at 4,500 m elevation in the Ecuadorian Andes. Copyright Dr. Morley Read
成績單
The first step in paleoclimatology is to collect, or extract, the biomarkers from the sediment they are found in. Environmental samples are composed of non-organic components, such as minerals, water, and metals, and organic components that are created by living organisms in the area. Before these organic components can be used by scientists to elucidate information about the past, they must be removed from their environment. Sonication, which utilizes ultrasonic waves, is the simplest and least expensive of these techniques.
This video is part of a series on lipid extraction, purification, and analysis from sediments. It will illustrate lipid extraction by ultrasound and present a few applications of the method.
Because of the wide range of biomarkers, there is no single solvent optimized to extract all of them. This is summarized by the so-called ‘like dissolves like’ rule, whereby relatively apolar molecules dissolve in apolar solvents such as dichloromethane, and more polar molecules dissolve in more polar solvents such as methanol. Solvent mixtures for the extraction of specific lipids or groups of lipids are generally optimized empirically.
To accelerate extraction and increase yield, a sonication system is used to apply ultrasound – waves with frequencies greater than 20 kHz, in conjunction with the solvent mixture. When these waves contact the liquid organic phase, they cause the formation of short-lived microbubbles of solvent vapors that rapidly grow and collapse. On collapsing, these bubbles release a tremendous amount of energy as mechanical shear, facilitating lipid solubilization and dramatically increasing the efficiency of extraction.
After the ultrasound assisted solvent-extraction process, the result is a crude extract preparation, called a total lipid extract, that is subjected to further purification to allow qualitative and quantitative examination of lipid signatures. Now that you understand some of the main principles behind lipid extraction by sonication, lets take a look at a protocol for how the procedure is performed.
Collect the necessary sample materials from a chosen location. Some examples are lacustrine and marine sediments, terrestrial soils, microbial cultures, or plant leaves. Collected material is frozen overnight. Following this it is freeze-dried in a freeze dryer for 2 to 3 days. Crush and homogenize the freeze-dried samples prior to extraction with a solvent-rinsed mortar and pestle. To remove organic contaminants, combust the required borosilicate glass pipettes, vials, and weighing tins in an oven. After allowing the glassware to cool in the oven, rinse the metal tools with a mixture of dichloromethane and methanol. Once the sample and glassware are prepared, the sonication procedure can begin.
From this step on, all containers and glassware should be combusted before use. Place the weighing tin on a scale and tare. Rinse the lab spatula with the solvent mixture, then, use it to transfer an appropriate mass of freeze-dried, homogenized sample into the weighing tin and record the mass. Carefully transfer the weighed sample into a labeled vial. Using the squirt bottle of DCM:MeOH, add enough that the sample is covered by 1 to 2 cm of solvent, and cap the vial. Place the vial on a waterproof rack, now ready for sonication. Place the rack directly into the sonication bath. Check that the water level in the sonication bath is just deep enough to submerge the sample vials up to the top of the extraction solvent. Sonicate for 30 minutes at room temperature. After sonication, remove the rack from the sonicator. Let the vials sit to allow sediment settling to occur.
Remove the dichloromethane-methanol upper phase from the extraction vial using a pipette and bulb, and transfer into another pre-weighed and labeled vial. Repeat the sonication process a total of three times for each sample. Collect the extracts into one vial. Allow extracted samples to dry in their vials, caps off, and in the hood, covered loosely with a piece of foil. Label as ‘extracted residue’ and store in the extraction solvent. Now that the biomarkers have been extracted, they must be purified before analysis can take place.
Sonication accelerates several solvent extraction processes and is widely used in geochemical studies. Many archeologists work with geochemists in order to reconstruct the environmental and cultural circumstances under which early human civilizations lived. Pottery, one of the oldest human inventions, when unearthed, can be found to contain residual molecular fossils from wine, rice, or other contents that were once stored within.
To unearth chemical evidence of substances absorbed onto the surfaces, small samples of pottery are sonicated in the presence of organic solvents and extracted compounds can be subsequently identified downstream by spectroscopic methods. This kind of analysis helps archeologists detect the kinds of resources that were available to ancient populations and reconstruct the conditions of their habitat.
Photosynthetic microalgae are found in marine and freshwater ecosystems. Because they grow in seawater-based media and their culture occupies significantly smaller areas, they are now being widely studied as a promising alternative to terrestrial plants for the production of biofuels.
To extract lipids from a microalgal biomass, these researchers describe a sonication-assisted solvent extraction. Acoustic cavitation during sonication effectively disrupts rigid microalgal cell walls in order to liberate lipids. Such techniques aid the characterization of new microalgae from the environment for the production of non-petroleum sources of energy.
You’ve just watched JoVE’s introduction to Sonication-Assisted Extraction of Biomarkers from Sediments. The following videos will explain how the extract is further purified for analysis.
Thanks for watching!