Source : Nicholas Timmons, Antonella Cooray, Ph.d., département de physique & astronomie, école de Sciences physique, University of California, Irvine, CA
L’objectif de cette étude est d’examiner la nature physique des deux types de frottement (i.e., statique et cinétique). La procédure comprendra à mesurer le coefficient de friction pour les objets coulissant horizontalement, ainsi qu’un plan incliné vers le bas.
Frottement n’est pas complètement élucidé, mais il est déterminé expérimentalement est proportionnelle à la force normale exercée sur un objet. Si un microscope zoome sur deux surfaces qui sont en contact, il révélerait que leurs surfaces sont très durs à petite échelle. Cela empêche les surfaces de glisser facilement passé un de l’autre. Combinant l’effet de surfaces rugueuses avec les forces électriques entre les atomes dans les matériaux peut-être expliquer la force de frottement.
Il existe deux types de friction. Frottement statique est présent lorsqu’un objet ne bouge pas et certains force est nécessaire pour obtenir cet objet en mouvement. Frottement cinétique est présent lorsqu’un objet est déjà en mouvement, mais ralentit en raison de la friction entre les surfaces de glissement.
Table 1. Coefficients of friction.
Block | ![]() |
![]() |
A | 0.68 | 0.60 |
B | 0.52 | 0.47 |
Table 2. Effect of weight and surface area on the force of friction.
Measurement | ![]() (N) |
Factor by which it is larger or smaller |
Block B on A | 16 | With ![]() |
Block A on B | 14 | With ![]() |
Small surface area | 5 | With ![]() |
Table 3. Angle of repose.
Block | Angle of repose ![]() (°) |
![]() |
A | 30 | 0.58 |
B | 24 | 0.45 |
The results obtained from the experiment match the predictions made by Equations 1 and 2. In step 1, the static friction was larger than the kinetic friction. This is always the case, as more force is required to overcome friction when an object is not already in motion. In step 2, it was confirmed that the force of friction was proportional to the weight of both blocks and the coefficient of kinetic friction of the block in contact with the table. The result of step 3 confirms that the surface area does not affect the force of friction. In step 4, the angle of repose can be approximated by Equation 3. The error associated with the lab comes from the difficulty of reading the force scale while maintaining a constant velocity for the sliding block. By taking several measurements and calculating the average, this effect can be reduced.
Friction is everywhere in our daily lives. In fact, it would not be possible to walk without it. If someone tried walking on a frictionless surface, he would go nowhere. It is only the friction between the bottom of his feet and the ground as his muscles push against the ground that propels him forward.
In almost every aspect of industry, engineers are trying to reduce friction. When two surfaces are in contact, there will always be friction. This can take the form of heat, such as the heat felt when someone quickly rubs her hands together. In industrial applications, this heat can damage machines. Friction forces also oppose the motion of objects and can slow done mechanical operations. Therefore, substances like lubricants are used to decrease the coefficient of friction between two surfaces.
Table 4. Example coefficients of friction.
Materials | ![]() |
wood on wood | 0.2 |
brass on steel | 0.44 |
rubber on concrete | 0.8 |
lubricated ball bearings | < 0.01 |
In this experiment, the coefficients of static and kinetic friction were measured for two different sliding blocks. The effect of mass on the force of friction was examined, along with the effect of surface area. Lastly, the angle of repose for a block on an inclined plane was measured.
The effects of friction are easily observed in everyday activities and yet the physical mechanisms that govern friction can be complex.
Friction is a force that opposes the motion of an object when it is in contact with a surface. At the microscopic level, it is caused by surface roughness of the materials in contact and intermolecular interactions. But one can overcome this force by application of an external force that is equal in magnitude.
The goal of this video is to demonstrate how to measure friction in a lab setting for objects sliding horizontally as well as down an inclined plane.
Before diving into the protocol, let’s revisit the concepts behind the frictional force. First, you need to know that there are two types of frictions – kinetic friction and static friction.
To understand kinetic friction, imagine you are in a rubber tube sliding across an infinite horizontal field of ice.
Although ice may be considered a smooth surface, if we look at the microscopic level, there are complex interactions between the two surfaces that cause friction. These interactions depend on surface roughness and attractive intermolecular forces.
The magnitude of this kinetic friction force is equal to the product of the coefficient of kinetic friction, or μK, which depends on the material-surface combination, and the normal force, or Fnorm that pushes the object and surface together.
Fnorm acts to support the object and is perpendicular to the interface. In this case, since the tube is on a level ground, the Fnorm is equal to and opposite the force of gravity, which is mg. Therefore, if you know the combined mass of you with the tube, and the coefficient of kinetic friction for rubber and ice, we can easily calculate the force of friction.
Kinetic friction can convert some of the tube’s kinetic energy into heat and will also reduce the momentum of the tube ultimately bringing it to rest.
Now, this is when static friction – the other type of friction – comes into play. This frictional force opposes movement of a static object and could be calculated by applying an external force. The applied force that eventually moves the object reveals the maximum static force.
The formula for maximum static force is the same as the one for kinetic friction, but the coefficient of static friction μS is typically greater than μK for the same material-surface combination.
Another way to overcome the maximum static force is by increasing the slope of the surface. At some angle, called the angle of repose or θR, the force pulling down the slope will equal the static friction force and the tube will begin to slide. This pulling force, which is the sine of the angle of repose times the force of gravity, equals the maximum static force, which is μS times product of m, g, and cosine of θR. By rearranging this equation, we can calculate the coefficient of static friction.
Now that we’ve learned the principles of friction, let’s see how these concepts can be applied to experimentally calculate the forces and coefficients of both kinetic and static friction. This experiment consists of a mass scale, a force scale, two metal pans with different coefficients of friction denoted as block 1 and 2, an adjustable incline plane, two 1000 g weights, and a protractor.
Add a 1000 g weight to each block and use the scale to measure the masses of the loaded blocks.
After connecting the force scale to block 1, pull the scale horizontally and note the force reading just before the block begins to slide. Record this maximal static friction force and repeat this measurement five times to obtain multiple data sets. Perform the same procedure using block 2 and record these values.
Next, with the force scale connected to block 1, pull the scale at a constant speed and note the kinetic friction force on the gauge. Repeat this measurement five times to obtain multiple data sets. Again, perform the same procedure using block 2 and record these values.
Now, place block 1 on top of block 2 and pull the scale at a constant speed to determine the kinetic friction force. Repeat this measurement five times and calculate the average. Then perform the same procedure with block 2 on top of block 1.
For the next experiment, turn block 1 such that the smaller surface area faces the table and attach it to the force scale. Now measure the static friction force as before by making note of the force before the block begins to slide. Repeat this measurement five times to obtain multiple data sets.
For the last experiment, place block 1 on the adjustable incline plane with the plane initially at an angle of zero degrees. Slowly raise the angle of the plane and use a protractor to determine the angle at which the block begins to slide. Again, repeat this measurement five times to obtain multiple data sets and perform the same procedure using block 2.
For the experiments performed on horizontal surface, the normal force on the blocks is equal to the weight, that is mass times g. Since the mass of block 1 and 2 for both static and kinetic friction experiments are the same, Fnorm is the same in all four cases. Using the average of the measured force values for the various experiments, and the formulae for both frictions, the coefficients of friction can be calculated.
As expected, the coefficient of static friction is greater than the coefficient of kinetic friction. Furthermore, the respective coefficients for the two blocks are different since they each possess a different surface roughness.
In the stacked blocks experiment, we know that the mass doubles in both cases, so we can calculate the new Fnorm. We already know μk for the block in contact with the surface. Using this we can calculate the kinetic friction force, which agrees well with the measured force during the experiment.
The friction force measured following a change in orientation of block 1 demonstrated that the contact surface area does not affect the force of friction. The discrepancies between the calculated and measured forces are consistent with the estimated errors associated with reading the force scale while maintaining a constant speed.
For the inclined plane experiments, the angle of repose was measured. Using this angle, the coefficients of static friction could be determined, and here the values compare favorably with the coefficients measured from the horizontal sliding measurements.
Studying friction is important in several applications, as it can either be highly beneficial or a phenomenon that must be minimized.
It is extremely important for automobile tire manufactures to study friction, as it allows tires to gain traction on a road. Therefore, when it rains, the water and residual oils on the road significantly reduce the coefficient of friction, making sliding and accidents much more likely.
While engineers want to increase friction for car tires, for engines and machinery in general they want to reduce it, as friction between metals can generate heat and damage their structures. Therefore, engineers constantly study lubricants that may help in decreasing the coefficient of friction between two surfaces.
You’ve just watched JoVE’s introduction to Friction. You should now understand what factors contribute to the magnitude of friction, the different types of friction, and the underlying physical mechanisms that govern it. As always, thanks for watching!