Summary

HKUST-1 as a Heterogeneous Catalyst for the Synthesis of Vanillin

Published: July 23, 2016
doi:

Summary

The conversion of trans-ferulic acid to vanillin was achieved by heterogeneous catalysis. HKUST-1 was employed in this synthesis and the essential step in the catalytic process was the generation of unsaturated metal sites. Thus, when the catalyst was activated under vacuum, full vanillin conversion (yield of 95%) was obtained.

Abstract

Vanillin (4-hydoxy-3-methoxybenzaldehyde) is the main component of the extract of vanilla bean. The natural vanilla scent is a mixture of approximately 200 different odorant compounds in addition to vanillin. The natural extraction of vanillin (from the orchid Vanilla planifolia, Vanilla tahitiensis and Vanilla pompon) represents only 1% of the worldwide production and since this process is expensive and very long, the rest of the production of vanillin is synthesized. Many biotechnological approaches can be used for the synthesis of vanillin from lignin, phenolic stilbenes, isoeugenol, eugenol, guaicol, etc., with the disadvantage of harming the environment since these processes use strong oxidizing agents and toxic solvents. Thus, eco-friendly alternatives on the production of vanillin are very desirable and thus, under current investigation. Porous coordination polymers (PCPs) are a new class of highly crystalline materials that recently have been used for catalysis. HKUST-1 (Cu3(BTC)2(H2O)3, BTC = 1,3,5-benzene-tricarboxylate) is a very well known PCP which has been extensively studied as a heterogeneous catalyst. Here, we report a synthetic strategy for the production of vanillin by the oxidation of trans-ferulic acid using HKUST-1 as a catalyst.

Introduction

The use of porous coordination polymers (PCPs) as heterogeneous catalysts1-4 is a relatively new research field. Due to very interesting properties that PCPs show, e.g., porous regularity, high surface area and metal access, they can offer new alternatives for heterogeneous catalysts5-6. The generation of catalytically active PCPs has been the main focus of many research groups7-10. A porous coordination polymer is constituted by metal ions and organic linkers and thus, the catalytic activity of these materials is provided by any of these parts. Some PCPs contain unsaturated (active) metals that can catalyze a chemical reaction11. However, the generation of unsaturated metal sites (open metal sites) within coordination polymers is not a trivial task and it represents a synthetic challenge that can be summarized in: (i) the generation of vacant coordination by removal of labile ligands7-11; (ii) the generation of bimetallic PCPs by incorporating organometallic ligands (previously synthesized)8,12-13; (iii) the post-synthetic variation of the metal ions9,14-15 or to the organic ligands10, 16-17 within the pores of the PCPs. Since the methodology (i) is the simplest thus, it is the most frequently used. Typically, the generation of open metal sites has been used for enhancing the affinity of PCPs towards H218-19, as well as for designing active heterogeneous catalysts20-27. In order to achieve good catalyst properties, PCPs need to show, additionally to the accessibility of open metal sites, retention of the crystallinity after the catalytic experiment, relatively high thermal stability and chemical stability to the reaction conditions.

HKUST-1 (Cu3(BTC)2(H2O)3, BTC = 1,3,5-benzene-tricarboxylate)7 is a well-investigated porous coordination polymer constructed with Cu(II) cations, that are coordinated to the carboxylate ligands and water. Interestingly, these water molecules can be eliminated (by heating) and this provides a square planar coordination around the copper ions which exhibit hard Lewis acid properties11. Bordiga and co-workers28 showed that the elimination of these H2O molecules did not affect the crystallinity (retention of the regularity) and the oxidation state of the metal ions (Cu(II)) was not affected. The use of HKUST-1 as a catalyst has been extensively investigated29-33 and in particular (very relevant for the present work) the oxidation with hydrogen peroxide of aromatic molecules34.

Vanilla is one of the most widely used flavoring agents in the cosmetic, pharmaceutical and food industries. It is extracted from the cured beans of the orchid Vanilla planifolia, Vanilla tahitiensis and Vanilla pompon. The Mayan and Aztec civilizations (pre-Columbian people) first realized the enormous potential of vanilla as a flavoring agent since it improved the chocolate flavor35-37. Vanilla was first isolated in 185838 and it was not until 187439 that the chemical structure of vanillin was finally determined. The natural extraction of vanillin (from the orchid Vanilla planifolia, Vanilla tahitiensis and Vanilla pompon) represents only 1% of the worldwide production and since this process is expensive and very long40, the rest of vanillin is synthesized40. Many biotechnological approaches can be used for the synthesis of vanillin from lignin, phenolic stilbenes, isoeugenol, eugenol, guaicol, etc. However, these approaches have the disadvantage of harming the environment since these processes use strong oxidizing agents and toxic solvents41-43. Herein, we report a synthetic strategy for the production of vanillin by the oxidation of trans-ferulic acid using HKUST-1 as a catalyst.

Protocol

CAUTION: The chemicals used in this catalytic procedure are relatively low in toxicity and non-carcinogenic. Please use all appropriate safety precautions when performing this experimental procedure such as safety glasses, gloves, lab coat, full length pants and closed-toe shoes. One part of the following procedures involves standard air-free handling techniques.

1. Activation of the Catalyst (HKUST-1)

  1. Crystallinity Characterization of the Catalyst
    Note: HKUST-1 is a commercially available porous coordination polymer (catalyst). In order to corroborate the crystallinity of the catalyst, samples of HKUST-1 need to be characterized by powder X-ray diffraction (PXRD).
    1. Collect a PXRD pattern of a 0.1 g sample of HKUST-1 (on a diffractometer operating at 160 W (40 kV, 40 mA)) for Cu-Kα1 radiation (λ = 1.5406 Å) in Bragg-Brentano geometry. Record a PXRD pattern from 5° to 60° (2θ) in 0.02° steps and 1 sec counting time44.
  2. Desolvation of HKUST-1
    1. Weigh 0.05 g of the catalyst (HKUST-1).
    2. Clamp a 250 ml two-neck round-bottom flask to a stand and insert a magnetic stirring bar into the round-bottom flask.
    3. Attach a condenser to the round-bottom flask.
    4. Use some vacuum grease or Teflon tape between the joints of the flask and condenser in order to generate a perfect seal.
    5. Connect the condenser, from the top, to a vacuum pump (via a stopcock to a hose).
    6. Make sure that the vacuum generated by the pump is approximately 10-2 bar.
      Note: For convenience, this experimental set up (the two-neck round-bottom flask attached to a condenser, which is connected to a vacuum pump) will be referred as the activation system.
    7. Place the catalyst (0.05 g) inside the 250 ml two-neck round-bottom flask.
    8. Insert a rubber septum in the second neck of the round bottom flask and make sure that it seals (fits) properly.
    9. Carefully, place the activation system into a sand bath.
    10. Start the vacuum pump and carefully turn the stopcock until it is fully open. With a hot plate, heat the activation system up to 100 °C for 1 hr.
    11. Stir at the lowest speed of the hot plate, in order to distribute homogenously the catalyst at the bottom of the round-bottom flask.
    12. Turn off the heat (hot plate) after 1 hr of heating, and let the activation system cool to room temperature (under vacuum).
    13. Once the activation system has cooled down to room temperature, turn the stopcock off (thus, the activation system would be under passive vacuum) and turn the pump off.
    14. Connect a balloon filled with nitrogen (N2), through the septum, to the two-neck round-bottom flask and wait a few seconds to reach the equilibrium pressure.
      Note: After the activation of the catalyst, leave it under an inert atmosphere (N2) since the access to the uncoordinated metal sites (or open metal sites) is the key to obtain an active catalyst.
    15. Remove the balloon filled with N2, when the equilibrium pressure has been achieved.
      Note: A color change from turquoise (as-received HKUST-1) to dark blue (upon activation) is observed.

2. Synthesis of Vanillin via Heterogeneous Catalysis

  1. Degassing of the Organic Solvent
    1. Degas approximately 70 ml of ethanol by bubbling N2 for 5 min.
  2. Preparation of the Catalytic Reaction
    1. Add 10 ml of degassed ethanol to the two-neck round-bottom flask and gently stir the suspension on a hot plate.
    2. Add 5 ml of H2O2 (30 % in H2O) to the suspension.
    3. Add 0.25 ml of acetonitrile to the suspension.
    4. Weigh 0.50 g of ferulic acid and dissolve it in 20 ml of degassed ethanol in a beaker.
    5. Add the dissolved ferulic acid to the suspension.
    6. Wash the beaker with 20 ml of degassed ethanol and add it to the suspension.
  3. Oxidation of Trans-ferulic Acid to Vanillin
    1. Unplug the hose that connects the condenser to the vacuum pump.
    2. Turn on the tap water that goes through the condenser. Preferably, use a water pump.
    3. Heat the suspension up to 100 °C (refluxing) for 1 hr.
    4. Turn off the heat and stirring. Carefully lift the two-neck round-bottom flask (attached to the condenser) and let it cool to room temperature.
  4. Work-up of the Reaction
    1. Filter off the reaction mixture (use a Buchner funnel and flask), recover the catalyst (HKUST-1) and wash it with 200 ml of ethyl acetate.
      Note: In order to speed up the filtration process, use a vacuum (connected to the Buchner flask) to quickly recover and wash the catalyst.
    2. Corroborate the retention of framework crystallinity of the catalyst by PXRD as in Section 1.
    3. Concentrate the combined organic phases (under vacuum with a rotary evaporator) and re-dissolve it with 100 ml ethyl acetate.
    4. Wash the organic phases (use a separation funnel) with a saturated solution of NH4Cl (30 ml).
    5. Recover the organic phases and mix them with anhydrous Na2SO4 (30 g). Let the suspension stand for 15 min.
    6. Filter the suspension off and recover the filtrate.
    7. Concentrate the filtrate (to approximately 20 ml) under vacuum with a rotary evaporator.
  5. Purification of the Residue (Vanillin)
    1. Purify the residue by flash column chromatography44. The stationary phase is silica gel and the mobile phase is a solvent mixture of ethyl acetate-hexane (5:95).
    2. Pack the glass column for chromatography (1 cm x 30 cm) with silica gel (1 cm x 6 cm). Saturate the column with acetate-hexane (5:95) solvent mixture.
    3. Pour carefully the concentrated-filtrate at top of the glass column.
    4. Slowly add the solvent mixture to the glass column and collect all of the fractions until 1,200 ml are collected.
    5. Concentrate the organic fractions (1,200 ml) with a rotary evaporator until dryness.
    6. Recover the final solid powder that is the purified vanillin.

Representative Results

Three representative samples of HKUST-1 were analyzed by infrared spectroscopy: non-activated, activated at 100 °C for 1 hr in an oven (exposed to air), and activated under vacuum (10-2 bar) at 100 °C for 1 hr. Thus, Fourier transform infrared (FTIR) spectra were recorded using a spectrometer with a single reflection diamond ATR accessory (Figure 1). For all spectra, 64 scans in the 4,000 to 400 cm-1 range were recorded with a spectral resolution of 4 cm-1.

In order to confirm the composition of purified product from oxidation of trans-ferulic acid using HKUST-1 as a catalyst, a 1H-NMR spectra was performed on a NMR spectrometer under a static magnetic field of 11.74 T at 25 °C (Figure 2). For that, a 5 mg sample was introduced into NMR test tube and 0.5 ml of deuterated chloroform (CDCl3) was added.

Figure 1
Figure 1: FTIR spectra of the catalyst (HKUST-1) at 25 °C. Non-activated (green line), activated in a conventional oven (purple line) and activated under vacuum (orange line). Reproduced from reference44 with permission from the Centre National de la Recherche Scientifique (CNRS) and the Royal Society of Chemistry. Please click here to view a larger version of this figure.

Figure 2
Figure 2: 1H-NMR spectra of vanillin after column chromatography purification on silica gel when the catalyst (HKUST-1) was activated under vacuum (10-5 bar) and 100 °C for 1 hr.

Discussion

The fundamental step for the catalytic conversion of trans-ferulic acid to vanillin was the activation of the catalyst (HKUST-1). If the catalyst is not activated in situ (under vacuum and at 100 °C), only partial conversion of trans-ferulic acid to vanillin was observed44. In other words, the accessibility to open metal sites is crucial for the catalytic cycle44, and this can be achieved by the elimination of coordinated water to the Cu(II) metal sites within the porous coordination polymer.

Therefore, in order to investigate this phenomenon three infrared experiments were carried out. The first experiment, the FTIR spectrum of a non-activated sample of HKUST-1 (Figure 1) showed the characteristic absorption bands at 3,400 cm-1 and 3,680 cm-1 corresponding to uncoordinated water (broad absorption band) and coordinated water (sharp absorption band), respectively. Second, the HKUST-1 sample activated in a conventional oven (exposed to air) showed a FTIR spectrum with minimal changes in comparison to the previous experiment: a decrease in the intensity of the absorption band at 3,400 cm-1 but no change on the sharp absorption band at 3,680 cm-1 (Figure 1). This change suggested an incomplete loss of uncoordinated water and the maintenance of coordinated water to the Cu(II) metal ion. Finally, the FTIR spectrum of the catalyst activated in situ exhibited two major changes (respect to the non-activated catalyst), a considerable reduction in the intensity of the absorption band at 3,400 cm-1 and a complete lost on the intensity of the absorption band at 3,680 cm-1. Thus, when the catalyst is activated under vacuum (10-2 bar) and at 100 °C, it is possible to get complete access to the Cu(II) open metal sites; the elimination of any water molecules (non and coordinated) inside the pores of HKUST-1.

Once the catalytic reaction is finished, the catalyst can be easily recovered by filtration and re-used (Figure 2)44. Of course, it has to be re-activated (under vacuum, 10-2 bar, and at 100 °C). In order to facilitate the re-activation process, once the catalyst is recovered, washing it up with approximately 200 ml of ethyl acetate is needed. Then, the catalyst can be left at room temperature (on the Buchner funnel) for 30 min, recovered and finally transferred into the activation system (vide supra).

The scaling up of the reaction is the current limitation of this experimental technique. The maximum amount of catalyst used was 0.05 g which resulted in a conversion yield of 95% (obtained after isolation of the vanillin by flash column chromatography)44. This catalytic reaction was carried out with higher quantities of catalyst (consequently, more ferulic acid and the rest of the chemicals) and the conversion yield dropped down significantly.

Only the combination of activated heterogeneous catalyst with hydrogen peroxide is needed to catalyze the oxidation of trans-ferulic acid. In order to discriminate the heterogeneous catalytic conversion, blank tests (one without HKUST-1 and another without H2O2) were performed44. After these reactions were completed, in the same conditions, the analysis of product composition did not show the presence of vanillin44.

The catalytic methodology presented in here showed how the heterogeneous catalyst (HKUST-1) can be used for the effective conversion of trans-ferulic acid to vanillin when it is activated in situ. Additionally the retention of the crystallinity of the catalyst was corroborated by PXRD44 after this was re-used. Previous synthetic vanillin methodologies use strong oxidizing agents and toxic solvents41-43. The current methodology completely avoids these hazards and it also offers the ability to re-use the heterogeneous catalyst (HKUST-1).

Finally, we are investigating the applicability of the catalytic technique for the oxidation of different α,β-unsaturated carboxylic acids.

Divulgations

The authors have nothing to disclose.

Acknowledgements

The authors thank Dr. A. Tejeda-Cruz (X-ray; IIM-UNAM). R.Y. thanks CINVESTAV, Mexico for technical support. M.S.S acknowledges the financial support by Spanish Government, MINECO (MAT2012-31127). I.A.I thanks CONACyT (212318) and PAPIIT UNAM (IN100415), Mexico for financial support. E.G-Z. thanks CONACyT (156801 and 236879), Mexico for financial support. Thanks to U. Winnberg (ITAM and ITESM) for scientific discussions.

Materials

HKUST-1 Sigma-Aldrich MFCD10567003
Ferulic Acid (trans-4-Hydroxy-3-methoxycinnamic acid) Sigma-Aldrich 537-98-4
Ethanol Sigma-Aldrich 64-17-5
Hydrogen peroxide solution Sigma-Aldrich  7722-84-1
Acetonitrile Sigma-Aldrich 75-05-8
Ethyl acetate Sigma-Aldrich 141-78-6
Ammonium chloride Sigma-Aldrich 12125-02-9
Sodium sulfate anhydrous Sigma-Aldrich 7757-82-6
Ethyl acetate Sigma-Aldrich 141-78-6
n-Hexane Sigma-Aldrich 110-54-3
Silica Gel Sigma-Aldrich 112926-00-8  Size 70/230
250 mL two-neck round-bottom flask Sigma-Aldrich Z516872-1EA 250 mL capacity
Magnetic stirring bar Bel-Art products 371100002 Teflon, octagon
Condenser Cole-Parmer JZ-34706-00 200 mm Jacket length
Vacuum pump (Approx. 10X-2 bar) Cole-Parmer JZ-78162-00 Vacuum/Pressure Diaphragm Pump
Stopcock Cole-Parmer EW-30600-00 with a male luer slip
Hose Cole-Parmer JZ-06602-04 16.0 mm ID and 23.2 mm ED
Rubber septums Cole-Parmer JZ-08918-34 Silicone with PTFE coating
Hot plate Cole-Parmer JZ-04660-15 10.2 cm x 10.2 cm, 5 to 540 °C
Sand bath  Cole-Parmer GH-01184-00 Fluidized Sand Bath SBS-4, 50 to 600 °C
N2 gas INFRA Cod. 103 Cylinder 9m ³
Ballons (filled with N2 gas) Sigma-Aldrich Z154989-100EA Thick-wall, natural latex rubber
Syringes with removable needles Sigma-Aldrich Z116912-100EA 10 mL capacity
Filter paper Cole-Parmer JZ-81050-24 Grade No. 235 qualitative filter paper (90 mm diameter disc)
Buchner funnel Cole-Parmer JZ-17815-04 320 mL capacity which accept standard paper filter sizes 
Buchner flask Cole-Parmer JZ-34557-02 250 mL capacity
Rotary Evaporator Cole-Parmer JZ-28710-02
Beakers Cole-Parmer JZ-34502-(02,04,05) Pyrex Brand 1000 Griffin; 20, 50 and 100 mL
Separation funnel  Cole-Parmer JZ-34505-44 Capacity for 125 mL with steam lenght of 60 mm
Glass column for chromatography Cole-Parmer JZ-34695-42 Column with fritted disk, 10.5 mm ID x 250 mm L
PXRD diffractometer Bruker AXS D8 Advance XRD
FTIR spectrophotometer Thermo scientific FT-IR (JZ-83008-02); ATR (JZ-83008-26) Nicolet iS5 FT-IR Spectrometer, with KBr Windows and iD5 Diamond ATR

References

  1. Corma, A., García, H., Llabrés i Xamena, F. X. Engineering Metal Organic Frameworks for Heterogeneous Catalysis. Chem. Rev. 110 (8), 4606-4655 (2010).
  2. Gascon, J., Corma, A., Kapteijn, F., Llabrés i Xamena, F. X. Metal Organic Framework Catalysis: Quo vadis?. ACS Catal. 4 (2), 361-378 (2014).
  3. Ranocchiari, M., van Bokhoven, J. A. Catalysis by metal-organic frameworks: fundamentals and opportunities. Phys. Chem. Chem. Phys. 13, 6388-6392 (2011).
  4. Dhakshinamoorthy, A., Alvaro, M., Garcia, H. Commercial metal-organic frameworks as heterogeneous catalysts. Chem. Commu. 48 (92), 11275-11288 (2012).
  5. Corma, A., García, H. Lewis Acids as Catalysts in Oxidation Reactions: From Homogeneous to Heterogeneous Systems. Chem. Rev. 102 (10), 3837-3892 (2002).
  6. Corma, A., García, H. Lewis Acids: From Conventional Homogeneous to Green Homogeneous and Heterogeneous Catalysis. Chem. Rev. 103 (11), 4307-4366 (2003).
  7. Chui, S. S. Y., Lo, S. M. F., Charmant, J. P. H., Orpen, A. G., Williams, I. D. A Chemically Functionalizable Nanoporous Material [Cu3(TMA)2(H2O)3]n. Science. 283 (5405), 1148-1150 (1999).
  8. Farha, O. K., Shultz, A. M., Sarjeant, A. A., Nguyen, S. T., Hupp, J. T. Active-Site-Accessible, Porphyrinic Metal−Organic Framework Materials. J. Am. Chem. Soc. 133 (15), 5652-5655 (2011).
  9. Zhang, J. P., Horike, S., Kitagawa, S. A Flexible Porous Coordination Polymer Functionalized by Unsaturated Metal Clusters. Angew. Chem. Int. Ed. 46 (6), 889-892 (2007).
  10. Wang, Z., Cohen, S. M. Postsynthetic modification of metal-organic frameworks. Chem. Soc. Rev. 38 (5), 1315-1329 (2009).
  11. Llabresi Xamena, F. X., Luz, J., Cirujano, F. G., Llabres i Xamena, F. X., Gascon, J. Chapter 7, Strategies for Creating Active Sites in MOFs. Metal organic frameworks as heterogeneous catalysts. , (2013).
  12. Cho, S. H., Ma, B., Nguyen, S. T., Hupp, J. T., Albrecht-Schmitt, T. E. A metal-organic framework material that functions as an enantioselective catalyst for olefin epoxidation. Chem. Commun. (24), 2563-2565 (2006).
  13. Xie, M. H., Yang, X. L., Wu, C. D. A metalloporphyrin functionalized metal-organic framework for selective oxidization of styrene. Chem. Commun. 47 (19), 5521-5523 (2011).
  14. Zhang, X., Llabrés i Xamena, F. X., Corma, A. Gold(III) – metal organic framework bridges the gap between homogeneous and heterogeneous gold catalysts. J. Catal. 265 (2), 155-160 (2009).
  15. Bohnsack, A. M., Ibarra, I. A., Bakhmutov, V. I., Lynch, V. M., Humphrey, S. M. Rational Design of Porous Coordination Polymers Based on Bis(phosphine)MCl2 Complexes That Exhibit High-Temperature H2 Sorption and Chemical. J. Am. Chem. Soc. 135 (43), 16038-16041 (2013).
  16. Ingleson, M. J., Perez-Barrio, J., Guilbaud, J. B., Khimyak, Y. Z., Rosseinsky, M. J. Framework functionalisation triggers metal complex binding. Chem. Commun. (23), 2680-2682 (2008).
  17. Burrows, A. D., Frost, C. G., Mahon, M. F., Richardson, C. Post-Synthetic Modification of Tagged Metal-Organic Frameworks. Angew. Chem. Int. Ed. 47 (44), 8482-8486 (2008).
  18. Dincă, M., Long, J. R. Hydrogen Storage in Microporous Metal-Organic Frameworks with Exposed Metal Sites. Angew. Chem. Int. Ed. 47 (36), 6766-6779 (2008).
  19. Ibarra, I. A., et al. Structures and H2 Adsorption Properties of Porous Scandium Metal-Organic Frameworks. Chem. Eur. J. 16 (46), 13671-13679 (2010).
  20. Gustafsson, M., et al. A Family of Highly Stable Lanthanide Metal−Organic Frameworks: Structural Evolution and Catalytic Activity. Chem. Mater. 22 (11), 3316-3322 (2010).
  21. Mitchell, L., et al. Remarkable Lewis acid catalytic performance of the scandium trimesate metal organic framework MIL-100(Sc) for C-C and C=N bond-forming reactions. Catal. Sci. Technol. 3 (3), 606-617 (2013).
  22. Jeong, K. S., et al. Asymmetric catalytic reactions by NbO-type chiral metal-organic frameworks. Chem. Sci. 2 (5), 877-882 (2011).
  23. Henschel, A., Gedrich, K., Kraehnert, R., Kaskel, S. Catalytic properties of MIL-101. Chem. Commun. (35), 4192-4194 (2008).
  24. Dhakshinamoorthy, A., et al. Iron(III) metal-organic frameworks as solid Lewis acids for the isomerization of α-pinene oxide. Catal. Sci. Techol. 2 (2), 324-330 (2012).
  25. Kurfiřtová, L., Seo, Y. K., Hwang, Y. K., Chang, J. S., Čejka, J. High activity of iron containing metal-organic-framework in acylation of p-xylene with benzoyl chloride. Catal. Today. 179 (1), 85-90 (2012).
  26. Beier, M. J., et al. Aerobic Epoxidation of Olefins Catalyzed by the Cobalt-Based Metal-Organic Framework STA-12(Co). Chem. Eur. J. 18 (3), 887-898 (2012).
  27. Ruano, D., Díaz-García, M., Alfayate, A., Sánchez-Sánchez, M. Nanocrystalline M-MOF-74 as Heterogeneous Catalysts in the Oxidation of Cyclohexene: Correlation of the Activity and Redox. Chem. Cat. Chem. 7 (4), 674-681 (2015).
  28. Prestipino, C., et al. Local Structure of Framework Cu(II) in HKUST-1 Metallorganic Framework:Spectroscopic Characterization upon Activation and Interaction with Adsorbates. Chem. Mater. 18 (5), 1337-1346 (2006).
  29. Opanasenko, M., et al. Comparison of the catalytic activity of MOFs and zeolites in Knoevenagel condensation. Catal. Sci. Technol. 3 (2), 500-507 (2013).
  30. Pérez-Mayoral, E., et al. Synthesis of quinolines via Friedländer reaction catalyzed by CuBTC metal-organic-framework. Dalton Trans. 41 (14), 4036-4044 (2012).
  31. Schlichte, K., Kratzke, T., Kaskel, S. Improved synthesis, thermal stability and catalytic properties of the metal-organic framework compound Cu3(BTC)2. Micropor. Mesopor. Mater. 73 (1-2), 81-88 (2004).
  32. Addis, D., et al. Hydrosilylation of Ketones: From Metal-Organic Frameworks to Simple Base Catalysts. Chem. Asian J. 5 (11), 2341-2345 (2010).
  33. Wu, Y., et al. Kinetics of oxidation of hydroquinone to p-benzoquinone catalyzed by microporous metal-organic frameworks M3(BTC)2 [M = copper(II), cobalt(II), or nickel(II); BTC = benzene-1,3,5-tricarboxylate] using molecular oxygen. Transition Met. Chem. 34 (3), 263-268 (2009).
  34. Marx, S., Kleist, W., Baiker, A. Synthesis, structural properties, and catalytic behavior of Cu-BTC and mixed-linker Cu-BTC-PyDC in the oxidation of benzene derivatives. J. Catal. 281 (1), 76-87 (2011).
  35. May, P., Cotton, S. . Molecules That Amaze Us. , 193 (2015).
  36. Havkin-Frenkel, D., Belanger, F. C. . Handbook of Vanilla Science and Technology. , 3 (2011).
  37. Zhao, S., et al. Preparation of ferulic acid from corn bran: Its improved extraction and purification by membrane separation. Food Bioprocess Technol. 92 (3), 309-313 (2014).
  38. Gobley, T. W. Recherche sur le principe odorant de la vanilla. J. Pharm. Chem. 3, 401 (1858).
  39. Tiemann, F., Haarmann, W. Uber das coniferin und seine Umwandlung in das aromatisches princip der vanilla. Ber. Dtsch. Chem. Ges. 7 (1), 608-623 (1858).
  40. Dignum, M. J. W., Kerler, J., Verpoorte, R. Vanilla production: technological, chemical, and biosynthetic aspects. Food. Rev. Int. 17 (2), 199-219 (2001).
  41. Walton, N. J., Mayer, M. J., Narbad, A. Vanilin. Phytochemistry. 63 (5), 505-515 (2003).
  42. Serra, S., Fuganti, C., Brenna, E. Biocatalytic preparation of natural flavours and fragrances. Trends Biotechnol. 23 (4), 193-198 (2005).
  43. Longo, M. A., Sanromán, M. A. Production of Food Aroma Compounds: Microbial and Enzymatic Methodologies. Food Technol. Biotechnol. 44 (3), 335-353 (2006).
  44. Yepez, R., et al. Catalytic activity of HKUST-1 in the oxidation of trans-ferulic acid to vanillin. New. J. Chem. 39 (7), 5112-5115 (2015).

Play Video

Citer Cet Article
Yépez, R., Illescas, J. F., Gijón, P., Sánchez-Sánchez, M., González-Zamora, E., Santillan, R., Álvarez, J. R., Ibarra, I. A., Aguilar-Pliego, J. HKUST-1 as a Heterogeneous Catalyst for the Synthesis of Vanillin. J. Vis. Exp. (113), e54054, doi:10.3791/54054 (2016).

View Video