Fonte: David Guo, College of Engineering, Technology, and Aeronautics (CETA), Southern New Hampshire University (SNHU), Manchester, New Hampshire
Um tubo pitot-estático é amplamente utilizado para medir velocidades desconhecidas no fluxo de ar, por exemplo, é usado para medir a velocidade do ar do avião. Pelo princípio de Bernoulli, a velocidade do ar está diretamente relacionada com variações de pressão. Portanto, o tubo pitot-estático sente a pressão estagnada e a pressão estática. Está conectado a um manômetro ou transdutor de pressão para obter leituras de pressão, o que permite a previsão da velocidade do ar.
Neste experimento, um túnel de vento é utilizado para gerar certas velocidades de ar, o que é comparado com as previsões do tubo estático pitot. Também é investigada a sensibilidade do tubo pitot-estático devido ao desalinhamento em relação à direção do fluxo. Este experimento demonstrará como a velocidade de fluxo de ar é medida usando um tubo estático pitot. O objetivo será prever a velocidade de fluxo de ar com base nas medições de pressão obtidas.
O princípio de Bernoulli afirma que um aumento na velocidade de um fluido ocorre simultaneamente com uma diminuição da pressão e vice-versa. Especificamente, se a velocidade de um fluido diminuir para zero, então a pressão do fluido aumentará ao máximo. Isso é conhecido como pressão de estagnação ou pressão total. Uma forma especial da equação de Bernoulli é a seguinte:
Pressão de estagnação = pressão estática + pressão dinâmica
onde a pressão de estagnação, Po, é a pressão se a velocidade de fluxo for reduzida a zero isentropicamente, a pressão estática, Ps,é a pressão que o fluido circundante está exercendo sobre um determinado ponto, e a pressão dinâmica, Pd, também chamada de pressão de carneiro, está diretamente relacionada com a densidade do fluido, ρ, e velocidade de fluxo, V,por um determinado ponto. Esta equação só se aplica ao fluxo incompressível, como fluxo líquido e fluxo de ar de baixa velocidade (geralmente menos de 100 m/s).
Da equação acima, podemos expressar velocidade de fluxo, V, em termos de diferencial de pressão e densidade de fluidos como:
No séculoXVIII, o engenheiro francês Henri Pitot inventou o tubo Pitot [1], e em meados do séculoXIX, o cientista francês Henry Darcy o modificou para sua forma moderna [2]. No início do séculoXX, o aerodinâmico alemão Ludwig Prandtl combinou a medição da pressão estática e o tubo Pitot no tubo estático pitot, que é amplamente utilizado hoje.
Um esquema de um tubo pitot-estático é mostrado na Figura 1. Há duas aberturas nos tubos: uma abertura enfrenta o fluxo diretamente para sentir a pressão de estagnação, e a outra abertura é perpendicular ao fluxo para medir a pressão estática.
Figura 1. Esquema de um tubo pitot-estático.
O diferencial de pressão é necessário para determinar a velocidade de fluxo, que normalmente é medida por transdutores de pressão. Neste experimento, um manômetro de coluna líquida é usado para fornecer um bom visual para medir a mudança de pressão. O diferencial de pressão é determinado da seguinte forma:
onde Δh é a diferença de altura do manômetro, ρL é a densidade do líquido no manômetro, e g é a aceleração devido à gravidade. Combinando equações 2 e 3, a velocidade de fluxo é prevista por:
Representative results are shown in Table 1 and Table 2. The results of the experiment are in good agreement with the actual wind speed. The Pitot-static tube accurately predicted the airspeed with a maximum percentage of error of approximately 4.2%. This can be attributed to errors in setting the wind tunnel airspeed, errors reading the manometer and instrument errors of the Pitot-static tube.
Table 1. Calculated airspeed and error based on manometer reading at various wind tunnel speeds.
Wind tunnel airspeed (mph) | Manometer reading (in. water) | Calculated airspeed (mph) | Percent error (%) |
50 | 1.1 | 48.04 | -3.93 |
60 | 1.6 | 57.93 | -3.45 |
70 | 2.15 | 67.16 | -4.06 |
80 | 2.8 | 76.64 | -4.20 |
90 | 3.6 | 86.90 | -3.45 |
100 | 4.4 | 96.07 | -3.93 |
110 | 5.4 | 106.43 | -3.25 |
120 | 6.5 | 116.77 | -2.69 |
130 | 7.8 | 127.91 | -1.61 |
Table 2. Calculated airspeed and error based on manometer reading at various angles of attach.
Pitot-Static Tube angle of attack (°) | Manometer readings (in water) | Calculated airspeed (mph) | Percent error (%) |
0 | 4.4 | 96.07 | 0.00 |
4 | 4.5 | 97.16 | 1.13 |
8 | 4.5 | 97.16 | 1.13 |
12 | 4.6 | 98.23 | 2.25 |
16 | 4.65 | 98.76 | 2.80 |
20 | 4.7 | 99.29 | 3.35 |
24 | 4.55 | 97.69 | 1.69 |
28 | 4.3 | 94.97 | -1.14 |
In Table 2, the percentage error is compared against the zero-angle case in Table 1. The results indicate that the Pitot-static tube is insensitive to misalignment with flow directions. The highest discrepancy occurred at an angle of attack of about 20°. A 3.35% error was obtained with respect to the zero angle reading. As the angle of attack increased, both the stagnation and static pressure measurements decreased. The two pressure readings tend to compensate each other so that the tube yields velocity readings that are accurate to 3 – 4% for angles of attack up to 30°. This is the chief advantage of the Prandtl design over other types of Pitot tubes.
Airspeed information is critical to aviation applications, such as for aircraft and drones. A Pitot-static tube is typically connected to a mechanical meter to show the airspeed at the front panel in the cockpit. For commercial aircraft, it is also connected to the onboard flight control system.
Errors in pitot-static system readings can be extremely dangerous. There are typically 1 or 2 redundant Pitot-static systems for commercial aircraft. To prevent ice buildup, the Pitot tube is heated during flight. Many commercial airline incidents and accidents have been traced to a failure of the Pitot-static system. For example, in 2008 Air Caraibes reported two incidents of Pitot tube icing malfunctions on its A330s [3].
In industry, the airspeed in duct and tubing can be measured with Pitot tubes where an anemometer or other flow meters would be difficult to install. The Pitot tube can be easily inserted through a small hole in the duct.
In this demonstration, the use of Pitot-static tubes was examined in a wind tunnel and the measurements were used to predict airspeed in the wind tunnel. The results predicted by the Pitot-static tube correlated well with the wind tunnel settings. The sensitivity of possible misalignment of the Pitot-static tube was also investigated and it was concluded that the Pitot-static tube is not particularly sensitive to misalignment up to and angle of attack of 28°.
Unknown speeds in an airflow, for example, the air speed of an aircraft, are typically measured using a pitot-static tube. The pitot-static tube is based on Bernoulli’s principle, where the increase in speed of a fluid is directly related to pressure variations.
The fluid itself exerts pressure on the surroundings, called static pressure. If the speed of the fluid is zero, the static pressure is at its maximum. This pressure is defined as the stagnation pressure, or total pressure.
As the fluid speed increases, it exerts static pressure on the surroundings as well as forces due to the velocity and density of the fluid. These forces are measured as the dynamic pressure, which is directly related to the fluid density and fluid velocity.
According to Bernoulli’s principle, the stagnation pressure is equal to the sum of the static pressure and dynamic pressure. Thus, if we are interested in determining the fluid velocity, we can substitute the equation for dynamic pressure and solve for the velocity as shown. The difference between the stagnation pressure and the static pressure is called the pressure differential, delta P.
So how do we measure the stagnation and static pressures in order to determine delta P and therefore velocity? This is where the pitot-static tube comes in.
A pitot-static tube has two sets of openings. One opening is oriented directly into the airflow, while a second set of openings is perpendicular to the airflow. The opening facing the flow senses the stagnation pressure, and the openings perpendicular to the flow sense the static pressure. The pressure differential, delta P, is then measured using either a pressure transducer or a fluid manometer.
A fluid manometer is a U-shaped tube containing a liquid. At ambient pressure, where delta P equals zero, the fluid in the manometer is level at an initial height. When the manometer experiences a pressure differential, the manometer fluid height changes, and we can read the change in height as delta h.
We can then calculate the pressure differential, delta P, which is equal to the density of the liquid in the manometer, times gravitational acceleration, times delta h. Then, by substituting the calculated pressure differential into our earlier equation, we can calculate the fluid speed.
In this experiment, you will measure different wind speeds in a wind tunnel using a pitot-static tube and a fluid manometer. You will then calculate the percent error in the air speed measurements collected using a misaligned pitot-static tube.
For this experiment, you will need access to an aerodynamic wind tunnel with a test section of 1 ft by 1 ft and a maximum operating air speed of 140 mph. You will also need a pitot-static tube and a manometer filled with colored oil, but marked as water-inch graduations.
Begin by connecting the two leads of the pitot-static tube fitting to the tube ports of the manometer using soft tubing. Now, open the test section and insert the pitot-static tube into the front threaded fittings. Orient the pitot-static tube so that the sensing head is in the center of the test section, pointing upstream. Use a handheld inclinometer to measure the angle of attack, and adjust the pitot tube to reach an angle of zero.Then close the front and top of the test section.
Now, turn on the wind tunnel, set the velocity to 50 mph, and observe the height difference on the manometer. Record the height difference. Next, increase the wind speed to 60 mph and again record the height difference on the manometer.
Repeat this procedure, increasing the wind speed, in increments of 10 mph, until the wind speed reaches 130 mph. Record the height difference on the manometer for each wind speed. Then, stop the wind tunnel and open the test section.
Using the handheld inclinometer, adjust the angle of attack to positive 4°. Then, close the test section and run the wind tunnel at 100 mph. Record the manometer height difference in your notebook. Repeat this procedure for angles of attack up to 28° using 4° increments. Record the manometer height difference for each angle at 100 mph.
Now, let’s take a look at how to analyze the data. First, recall that the stagnation pressure, or the pressure with zero flow speed, is equal to the static pressure plus the dynamic pressure. The dynamic pressure is directly related to the fluid density and flow speed. We can rearrange the equation to express flow speed in terms of the pressure differential and the fluid density.
The pressure differential is measured using the manometer, where the pressure differential is equal to the density of the liquid times g times the height difference in the manometer. Thus, flow velocity is predicted by the equation shown.
The air density, water density, and gravitational acceleration are known. Using the manometer height difference for each wind tunnel air speed at zero angle of attack, calculate the air speed measured by the pitot-static tube. As you can see, the percent error is quite small, showing that the pitot-static tube can predict air speed accurately, with error introduced from wind tunnel air settings, manometer readings, and other instrument errors.
Now, calculate the air speed at various angles of attack when the wind tunnel was operated at 100 mph. As you can see, the calculated air speeds are quite close to what is expected.
The percent difference is calculated by comparing the calculated air speed to the air speed measured at zero angle of attack. All differences are below 4% for the angles measured, showing that the pitot-static tube is generally insensitive to misalignment with the flow direction.
In summary, we learned how pitot-static tubes use Bernoulli’s principle to determine the speed of a fluid. We then generated a range of air speeds in a wind tunnel and used a pitot-static tube to measure the different air speeds. This demonstrated the predictive sensitivity of the pitot-static tube.